Space under an element between the finish floor or ground and 9 inches (230 mm) above the finish floor or ground shall be considered toe clearance and shall comply with 306.2....
Search Results "9-1-1 Service"
-
306.2.1 General
-
Section 35.151(b)(3) Alterations to historic facilities
Section 35.151(b)(3) Alterations to historic facilities The final rule renumbers the requirements for alterations to historic facilities enumerated in current Sec. 35.151(d)(1) and (2...
-
1016.5 Obstacles
Obstacles on outdoor recreation access routes, passing spaces, and resting intervals shall not exceed 1/2 inch (13 mm) in height measured vertically to the highest point....
-
M301.2.1 Adjustability (Section-by-Section Analysis)
As discussed in Section IV.B.1.a....
-
Sloped Entries
Sloped Entries Sloped entries must comply with ADAAG accessible route provisions (36 inch minimum width, maximum 1:12 or 8.33% slope), except that the surface does not need to be slip...
-
Obstructions [4.7.8]
Where space at the top is less than 48 inches, side flares must have a maximum slope of 1:12 instead of 1:10 at the curb face....
-
1016.5 Obstacles
Obstacles on outdoor recreation access routes, passing spaces, and resting intervals shall not exceed 1/2 inch (13 mm) in height measured vertically to the highest point....
-
1014.2.1 Transfer Access
The surface of the clear ground space is required to be firm and stable, and to slope not steeper than 1:48 in any direction....
-
Section 35.151(b)(3) Alterations to historic facilities (Section-by-Section Analysis)
) Alterations to historic facilities (Section-by-Section Analysis) The final rule renumbers the requirements for alterations to historic facilities enumerated in current § 35.151(d)(1)...
-
11B-1009.2.1 Pool lift location
Exceptions: 1. Where the entire pool depth is less than 36 inches (914 mm) or greater than 48 inches (1219 mm), compliance with Section 11B-1009.2.1 shall not be required....
-
Alterations
Normal maintenance, such as reroofing, painting, or wallpapering, is not an alteration. 2010 ADA Standards Basics Chapter 1: Application and Administration Contains important...
-
SAMPLE SCENARIO: EXTREME HEAT
DAY 1: The heat index has exceeded 100 degrees for the third day in a row. Meteorologists predict these conditions to continue for the next four days....
-
III-3.8000 Direct threat
The individual assessment must be based on reasonable judgment that relies on current medical evidence, or on the best available objective evidence, to determine -- 1) The nature, duration...
-
Technical Memorandum TM 2017-25 Door and Gate Surfaces
TM 2017-25 Door and Gate Surfaces Effective Date: April 1, 2017 2012 TAS Reference: 404.2.10 404.2.10 requires door and gate surfaces within 10 inches (255mm) of the finish...
-
GUARD OR GUARDRAIL
GUARD [DSA-AC , HCD 1 & HCD 2] OR GUARDRAIL. ...
-
804.6.2 Operable Parts
EXCEPTIONS: 1. Appliance doors and door latching devices shall not be required to comply with 309.4. 2....
-
1008.2.6.1 Accessibility
Ground surfaces shall comply with ASTM F 1951 (incorporated by reference, see "Referenced Standards" in Chapter 1)....
-
408.1 General
Limited-use/limited-application elevators shall comply with 408 and with ASME A17.1 (incorporated by reference, see "Referenced Standards" in Chapter 1)....
-
ACCESSIBILITY
[DSA-AC & HCD 1-AC] Accessibility is the combination of various elements in a building, facility, site, or area, or portion thereof which allows access, circulation and the full use...
-
804.6.2 Operable Parts
EXCEPTIONS: 1. Appliance doors and door latching devices shall not be required to comply with 309.4. 2....
-
T405.3 Visual Contrast
The stripe shall be 1 inch (25 mm) wide minimum and shall contrast visually with the rest of the step tread or circulation path surface either light-on-dark or dark-on-light....
-
1i
Are all of the small showers free of curbs or lips greater than 1/2" high at the shower floor that would impede wheelchair approach and transfer onto the folding shower seat?...
-
4(4)
Thresholds and changes in level at these locations are beveled with a slope no greater than 1:2....