provide a clearance 39 inches (990 mm) wide minimum, 6 inches (150 mm) high minimum measured from the floor, and 36 inches (915 mm) deep minimum measured from the edge of the examination surface...
Search Results "Door Surface"
Commonly Searched Documents
-
M301.4.1 Clearance in Base
-
102 Dimensions for Adults and Children
are also provided based on children’s dimensions and anthropometrics for drinking fountains, water closets and other elements located in toilet compartments, lavatories and sinks, dining surfaces...
-
703.4.1 Height Above Finish Floor or Ground
Tactile characters on signs shall be located 48 inches (1220 mm) minimum above the finish floor or ground surface, measured from the baseline of the lowest tactile character and 60 inches...
-
703.4.1 Height Above Finish Floor or Ground
Tactile characters on signs shall be located 48 inches (1220 mm) minimum above the finish floor or ground surface, measured from the baseline of the lowest tactile character and 60 inches...
-
Ramps [4.8]
The curvature and slope typically result in an uneven surface that makes wheelchair maneuvering difficult because not all wheels rest on the surface....
-
Openings in Beach Access Routes
Openings are gaps in the surface of a beach access route. Gaps include spaces between the planks on a boardwalk and drainage holes in temporary or permanent surfaces....
-
Questionnaire
A full version of the questionnaire given to the subjects after traveling over each surface can be found in Appendix C. The questionnaire was developed by the study investigators....
-
M302.4.1 Clearance in Base
provide a clearance 44 inches (1120 mm) wide minimum, 6 inches (150 mm) high minimum measured from the floor, and 36 inches (915 mm) deep minimum measured from the edge of the examination surface...
-
M301.4.1 Clearance in Base
provide a clearance 44 inches (1120 mm) wide minimum, 6 inches (150 mm) high minimum measured from the floor, and 36 inches (915 mm) deep minimum measured from the edge of the examination surface...
-
11B-801.1 Scope
For example, Section 11B-806 addresses guest rooms in transient lodging facilities while Section 11B-902 contains the technical specifications for dining surfaces....
- PEMKO 5" Latching Panic Saddle Threshold No. 2705-T
- Clarity AL10 Visual Alert System informational Video
-
11B-216.4.2 Areas of refuge and exterior areas for assisted rescue
Signs required by Chapter 10, Section 1007.9 at doors to areas of refuge and exterior areas for assisted rescue shall comply with Section 11B-703.5 and include an International Symbol of...
-
11B-612.2 Bench
Doors shall not swing into the clear floor space required by Section 11B-903.2....
-
Basic Features
Careful planning and design will incorporate elements such as a wider entrance door, adequate clear floor space, appropriate placement and models of fixtures and furniture, and grab bars...
-
Dressing, Fitting, or Locker Rooms
There must be an accessible route through the door and to all elements required to be accessible in the room....
-
H15
Is at least one wide toilet stall provided with an out swinging door, side and rear grab bars, and clear space next to the toilet?...
-
11B-612.2 Bench
Doors shall not swing into the clear floor space required by Section 11B-903.2....
-
11B-703.7.2.6.2 Women’s toilet and bathing facilities
The circle symbol shall contrast with the door, either light on a dark background or dark on a light background....
-
¾ Inch Minus and ¼ Inch Minus Limestone
The surface stayed soft under foot, enough to see footprints compacted and not return to the surface, but did not show any signs of erosion....
-
Soiltac Liquid Topical
The first noticeable signs of change for this surface came after the first heavy rainfall at the March 2008 testing....
-
Walk
An exterior prepared surface for pedestrian use, including pedestrian areas such as plazas and courts....
-
705.1 General
Detectable warnings shall consist of a surface of truncated domes and shall comply with 705....
-
Ramp
Ramp - A walking surface that has a running slope of greater than 1:20....