satin finish Holds 500 seat covers Seat cover dispenser is partition mounted Product Specs Body: Fabricated of #22 gauge stainless steel with a #4 satin finish on all exposed surfaces...
Search Results "Side Transfer Surface"
-
AJW Architectural Products U852 Dual Stall Seat Cover Dispenser - Partition Mounted
-
AJW Architectural Products U852H Dual Stall Seat Cover Dispenser w/ Flush Mounting - Partition Mounted
satin finish Holds 500 seat covers Seat cover dispenser is partition mounted Product Specs Body: Fabricated of #22 gauge stainless steel with a #4 satin finish on all exposed surfaces...
-
Limitations
Limitations The study is limited in scope by the following: Ability to generalize findings to trails in other locations with the same surfaces applied....
-
Future Work
The devices that are on the market to measure roadway roughness are not applicable to sidewalk and pedestrian surfaces because they either use accelerometers to measure the surface profile...
-
5. Bed with clear floor space
Bed with clear floor space for a side approach next to bed....
-
Ramps
Provide handrails on each side of the ramps at the following locations:...
-
Figure M2: M301.4 Lift Compatibility
(at Diagnostic Equipment for Use by a Patient in a Supine, Prone, or Side-Lying Position)...
-
F105.2.3 ASTM
ASTM F 1292-99 and ASTM F 1292-04 establish a uniform means to measure and compare characteristics of surfacing materials to determine whether materials provide a safe surface under and...
-
105.2.3 ASTM
ASTM F 1292-99 and ASTM F 1292-04 establish a uniform means to measure and compare characteristics of surfacing materials to determine whether materials provide a safe surface under and...
-
105.2.3 ASTM
ASTM F 1292-99 and ASTM F 1292-04 establish a uniform means to measure and compare characteristics of surfacing materials to determine whether materials provide a safe surface under and...
-
Zurn Industries Trap Protector
Antimicrobial, resists thermal transfer, and is ADA compliant. Fits 1 1/2 [38] maximum, tubular and semi-cast P traps....
-
R305.2.1 Perpendicular Curb Ramps
On perpendicular curb ramps, detectable warning surfaces shall be placed as follows: 1....
-
11B-809.10.8.7 Mirrors and towel bars
Where mirrors are provided the bottom edge of the reflective surface shall be 40 inches (1016 mm) maximum above the finish floor....
-
11B-403.5 Clearances
Walking surfaces shall provide clearances complying with Section 11B-403.5....
-
11B-403.5 Clearances
Walking surfaces shall provide clearances complying with Section 11B-403.5....
-
11B-809.10.8.7 Mirrors and towel bars
Where mirrors are provided the bottom edge of the reflective surface shall be 40 inches (1016 mm) maximum above the finish floor....
-
Vehicle Parking
in "Surfaces for Outdoor Recreation Access Routes" of this guidebook....
-
11B-606.3 Height
Lavatories and sinks shall be installed with the front of the higher of the rim or counter surface 34 inches (864 mm) maximum above the finish floor or ground....
-
11B-606.3 Height
Lavatories and sinks shall be installed with the front of the higher of the rim or counter surface 34 inches (864 mm) maximum above the finish floor or ground....
-
6. Grab Bars
Is there a horizontal grab bar at the head of the tub that is at least 12" long for stabilization and aid in transfer from a wheelchair to the fixed tub seat - see Figure 34 on page 25?...
-
R409.2 Where Required
Handrails shall be provided on both sides of ramps and stairways....
-
410.6 Doors and Gates
Side doors and gates shall provide a clear width 42 inches (1065 mm) minimum....
-
4.34.6.8* REFRIGERATOR/FREEZER
Provision shall be made for refrigerators which are: (1) Of the vertical side-by-side refrigerator/freezer type; or (2) Of the over-and-under type and meet the following requirements...
-
11B-705.1.2.2.1 Perpendicular curb ramps
Detectable warnings shall extend the full width of the ramp run less 2 inches (51 mm) maximum on each side, excluding any flared sides....
