Alternate roll-in type shower compartments shall be 36 inches (915 mm) wide and 60 inches (1525 mm) deep minimum clear inside dimensions measured at center points of opposing sides....
Search Results "Absolute Dimension"
-
608.2.3 Alternate Roll-In Type Shower Compartments
-
1016.6 Openings
Elongated openings should be placed so that the long dimension is perpendicular, or as close to perpendicular as possible, to the dominant direction of travel....
-
11B-703.6.1 Pictogram field
The 6-inch vertical dimension applies to the field, not the symbol. The symbol may be smaller than the field....
-
Section 1193.21 Accessibility, usability and compatibility (Section-by-Section Analysis)
As proposed, the obligations to provide usable documentation seemed to be absolute....
-
C101.4 Units of Measurement (Section-by-Section Analysis)
This proposed section is new to the 255 Guidelines, and would clarify dimensions stated in the text of the guidelines or referenced standards....
-
1016.6 Openings
Elongated openings should be placed so that the long dimension is perpendicular, or as close to perpendicular as possible, to the dominant direction of travel....
-
R304.2.1 Turning Space
The 1.5 m (5.0 ft) dimension shall be provided in the direction of the ramp run....
-
5.2.2.1 Transfer Surface Width Recommendations for M302
Rationale for final recommendation The Committee considered the dimensions for rectangular seats in roll-in showers from the 2010 Standards; and the ideal chair width recommended in Architectural...
-
R304.3.1 Turning Space
The 1.5 m (5.0 ft) dimension shall be provided in the direction of the pedestrian street crossing....
-
4.30.4* Raised and Brailled Characters and Pictorial Symbol Signs
The border dimension of the pictogram shall be 6 in (152 mm) minimum in height....
-
Controls
Consider push plates at least 3 inches in the least dimension since they do not require fine motor coordination or visual acuity to operate....
-
10.2.1(3)
Signs that are sized to the maximum dimensions permitted under legitimate local, state or federal regulations or ordinances shall be considered in compliance with 4.30.2 and 4.30.3 for purposes...
-
1016.6 Openings
Elongated openings should be placed so that the long dimension is perpendicular, or as close to perpendicular as possible, to the dominant direction of travel....
-
Knee Clearance: Clearance as Measured from Distal Knee Point - Manual Wheelchair
It references dimensions of clearance height and depth to the distal knee point on a person....
-
Knee Clearance: Clearance as Measured from Anterior-Most Abdomen Point - Manual Wheelchair
It references dimensions of clearance height and depth to the forward-most abdomen point on a person....
-
11B-703.6.1 Pictogram field
The 6-inch vertical dimension applies to the field, not the symbol. The symbol may be smaller than the field....
-
5.9.2.1 Standing Supports on Single Ramped Entry Raised Platforms with Wheelchair Spaces Recommendations
This dimension allows a user to grab it from any point on the platform....
-
B. Slopes
.: in the direction of travel) not more than 1:20 (critical dimension of 1 1/4" or less)?...
-
What is an Accessible Seat and Who Can Use One?
Accessible seats are spaces specifically designed for wheelchairs and include features such as an accessible approach, location at grade, clear floor space, and larger dimensions....
-
The Purpose of FSORAG and FSTAG
The building blocks for accessible design are based mostly on wheelchair dimensions, clear space, maneuvering room, and reach ranges found in ABAAS because the dimensions, multiple moving...
-
M301.4 Lift Compatibility
The dimensions there are 150mm x 1000mm. Recommendation here is to shrink the 1120mm dimension to 1000mm (39”) dimension to harmonize with the international standard....
-
Transfer Surface Height (M301.2.1 and M302.2.1)
Patient support surfaces can be adjusted to heights outside the specified dimensions when not needed for patient transfer such as when performing diagnostic procedures....
-
Exceptions Considered for Wheelchair Spaces on Raised Platforms
Comments should include information on sources to support the dimensions, where possible....