Recommendation: Dimensions for turns around obstructions in 4.3.3 (ADAAG Figure 7) provide minimum space for maneuvering around stacks where a cross aisle at the end of stacks is not provided...
Search Results "Absolute Dimension"
Filters
Commonly Searched Documents
-
Stacks [8.5]
-
11B-303.5 Warning curbs
Abrupt changes in level exceeding 4 inches (102 mm) in a vertical dimension between walks, sidewalks or other pedestrian ways and adjacent surfaces or features shall be identified by warning...
-
11B-405.7.2.1
Handrail extensions are not permitted to obstruct required clear landing dimensions except as allowed by the exception to Section 11B-307.2....
-
11B-609.3 Spacing
The distance between the grab bar and wall is an exact dimension. Many disabled people rely heavily upon grab bars to maintain balance and prevent serious falls....
-
11B-405.7.5 Doorways
Doors, in any position, shall not reduce the minimum dimension of the ramp landing to less than 42 inches (1067 mm). [2010 ADA Standards] 405.7.5 Doorways....
-
Ultratec Uniphone 1140 TTY
VCO calls can be made through a toll-free relay service, or directly between Uniphone users for absolute privacy....
-
Sampling Strategies
Age is a continuous variable, along which anthropometric dimensions change continuously....
-
304 Turning Space
The Department recognizes that the technical specifications for T-shaped and circular turning spaces in the 1991 and 2010 Standards, which are based on manual wheelchair dimensions, may...
-
Observations:
Observations: Wheelbase dimensions for manual wheelchairs and rear-wheel drive power chairs were similar to each other but slightly less than the wheelbase for front wheel drive...
-
Exterior Routes
Floor and ground surfaces stable, firm and slip resistant. 11B-302.1 Openings in floor or ground surfaces 1/2 inch maximum with long dimension...
-
Exterior Routes
Floor and ground surfaces stable, firm and slip resistant. 11B-302.1 Openings in floor or ground surfaces 1/2 inch maximum with long dimension...
-
2. REGULATORY BUILT-IN TOLERANCES
REGULATORY BUILT-IN TOLERANCES: California Building Code Section 1101B.5 indicates all dimensions are subject to conventional industry tolerances except where the requirement is stated as...
-
208.1.2
The facility may not reduce the required number or dimensions of those spaces, or unnecessarily increase the length of the accessible route from a parking space to the facility....
-
407.12.3.2.1 Height (Section-by-Section Analysis)
These dimensions and their resulting geometry are consistent with the ADA and ABA Accessibility Guidelines (36 CFR Part 1191, Appendix D, sections 306 and 308)....
-
4.35.4 Bench
Every accessible dressing room shall have a 24 in by 48 in (610 mm by 1220 mm) bench fixed to the wall along the longer dimension....
-
11B-812.6 Vehicle spaces
Where the long dimension of vehicle spaces is parallel to the traffic flow in the adjacent vehicular way, the length of vehicle spaces shall be 240 inches (6096 mm) minimum. 2....
-
B. Restrooms
These specifications are derived from requirements for rail vehicles and represent compromises between space needed for use and constraints imposed by vehicle dimensions....
-
11B-812.6 Vehicle spaces
Exceptions: Where the long dimension of vehicle spaces is parallel to the traffic flow in the adjacent vehicular way, the length of vehicle spaces shall be 240 inches (6096 mm) minimum...
-
Section 1193.37 Information pass-through [1193.27 in the NPRM] (Section-by-Section Analysis)
Also, this provision is subject to the readily achievable criteria so that the obligation is not absolute....
-
Section 36.211 Maintenance of Accessible Features (Preamble, Section-by-Section Analysis)
Some commenters objected that this section appeared to establish an absolute requirement and suggested that language from the preamble be included in the text of the regulation....
-
§35.133 Maintenance of Accessible Features
Some commenters objected that this section appeared to establish an absolute requirement and suggested that language from the preamble be included in the text of the regulation....
-
18 Inch Low Height
Finally, a majority of committee members proposed a range for the low height of 17 to 19 inches rather than establishing an absolute minimum....
-
§35.133 Maintenance of accessible features (Section-by-Section Analysis)
Some commenters objected that this section appeared to establish an absolute requirement and suggested that language from the preamble be included in the text of the regulation....
-
Section 36.211 Maintenance of Accessible Features (Section-By-Section Analysis and Response to Comments)
Some commenters objected that this section appeared to establish an absolute requirement and suggested that language from the preamble be included in the text of the regulation....
