Exceptions: Where the long dimension of vehicle spaces is parallel to the traffic flow in the adjacent vehicular way, the length of vehicle spaces shall be 240 inches (6096 mm) minimum...
Search Results "Absolute Dimension"
-
11B-812.6 Vehicle spaces
-
304 Turning Space
The Department recognizes that the technical specifications for T-shaped and circular turning spaces in the 1991 and 2010 Standards, which are based on manual wheelchair dimensions, may...
-
Observations:
Observations: Wheelbase dimensions for manual wheelchairs and rear-wheel drive power chairs were similar to each other but slightly less than the wheelbase for front wheel drive...
-
Exterior Routes
Floor and ground surfaces stable, firm and slip resistant. 11B-302.1 Openings in floor or ground surfaces 1/2 inch maximum with long dimension...
-
Exterior Routes
Floor and ground surfaces stable, firm and slip resistant. 11B-302.1 Openings in floor or ground surfaces 1/2 inch maximum with long dimension...
-
Sampling Strategies
Age is a continuous variable, along which anthropometric dimensions change continuously....
-
Guldmann Fixed Ramp Solution For Trains
Read more about the standard Lite ramp which is the absolute lightest on the market due to a unique material composition of glass and graphite fibre....
-
Self Contained, Closed Products - Side Reach Range
Requires the Accessibility Specialist plan or above. (Login or upgrade your account!)
-
Seating Locations
These dimensions allow people using mobility devices (e.g., wheelchairs, scooters, walkers, canes, and crutches) to independently enter and exit the room and move throughout the space, sit...
-
5.4.4.1 Transfer Support Distance from Transfer Surface Recommendation for Stretchers
The Committee proposes that this horizontal dimension be included for stretchers under the proposed rule....
-
A4.23.3 Clear Floor Space
The specific shower shown is designed to fit exactly within the dimensions of a standard bathtub....
-
A4.30.4 Raised and Brailled Characters and Pictorial Symbol Signs (Pictograms)
The standard dimensions for literary Braille are as follows: Dot diameter .059 in. Inter-dot spacing .090 in....
-
Clear Floor Space [4.20.2]
Clear Floor Space [4.20.2] Clear floor space at tubs, which is dimensioned according to the approach, may overlap required turning space within the room....
-
4.1.6(4)(a)
Table 2 -- Allowable Ramp Dimensions for Construction in Existing Sites, Buildings, and Facilities Slope* Maximum Rise Maximum Run Steeper than 1...
-
Section 1193.37 Information pass-through [1193.27 in the NPRM] (Section-by-Section Analysis)
Also, this provision is subject to the readily achievable criteria so that the obligation is not absolute....
-
Section 36.211 Maintenance of Accessible Features (Preamble, Section-by-Section Analysis)
Some commenters objected that this section appeared to establish an absolute requirement and suggested that language from the preamble be included in the text of the regulation....
-
§35.133 Maintenance of Accessible Features
Some commenters objected that this section appeared to establish an absolute requirement and suggested that language from the preamble be included in the text of the regulation....
-
18 Inch Low Height
Finally, a majority of committee members proposed a range for the low height of 17 to 19 inches rather than establishing an absolute minimum....
-
§35.133 Maintenance of accessible features (Section-by-Section Analysis)
Some commenters objected that this section appeared to establish an absolute requirement and suggested that language from the preamble be included in the text of the regulation....
-
Section 36.211 Maintenance of Accessible Features (Section-By-Section Analysis and Response to Comments)
Some commenters objected that this section appeared to establish an absolute requirement and suggested that language from the preamble be included in the text of the regulation....
-
Wall furr-out to support a grab bar when toilet is too far from the side wall
It's like what Daniel is describing but I'm not sure about the exact dimensions or construction details of the one in these photos....
-
Medical Device Manufacturers
supports; • Question 19 (c) on location and size of transfer supports; • Question 23 (a) on stirrups; • Question 24 (b) on positioning supports; • Question 29 (a) on alternative dimension...
-
Q5.) What dimensions and conditions can practitioners reasonably consider to be compliant when the conditions, as constructed, do not meet the technical requirements exactly and there are no official, published, industry-developed tolerances?
A5.) This is the most difficult question and the most subject to varying opinions. Sloped concrete and asphalt surfaces are an excellent example of this problem. To our...
-
§382.67(a)
stowage of cargo in the cabin compartment) in the cabin of sufficient size to stow at least one typical adult-sized folding, collapsible, or break-down manual passenger wheelchair, the dimensions...
