Section 608.2.3 covers the current ADA Standards for the size and clearances of alternate roll-in type shower compartments.
Search Results "Measuring Technique"
Filters
Commonly Searched Documents
-
Alternate Roll-In Type Shower Compartments: ADA Standard Section 608.2.3
-
11B-608.2.3 Alternate roll-in type shower compartments
Alternate roll-in type shower compartments shall be 36 inches (914 mm) wide and 60 inches (1524 mm) deep minimum clear inside dimensions measured at center points of opposing sides....
-
11B-404.2.4.3 Recessed doors and gates
457 mm) of the latch side at an interior doorway, or within 24 inches (610 mm) of the latch side of an exterior doorway, projects more than 8 inches (203 mm) beyond the face of the door, measured...
-
Wetland Trail Design and Construction
Some of the techniques and tools we describe are suitable for wilderness situations where mechanized equipment cannot be used....
-
Seeger et al.
Both unoccupied and occupied dimensions of device width and length were measured as well as a set of other basic dimensions....
-
Character Height: ADA Standard Section 703.2.5
Character height measured vertically from the baseline of the character shall be 5/8 inch (16 mm) minimum and 2 inches (51 mm) maximum based on the height of the uppercase letter “I”....
-
1.2.7
1.2.7 When local variations (flatness) for cross slope of ramps are measured according to 1.1.14 at least 80% (rounded to the nearest whole number) should not exceed a 2% slope....
-
Introduction
Dimension definitions and measurement techniques vary from study to study and, in many cases, samples were very small....
-
Original research for ANSI A117.1 (1957 - 1961)
1961, American National Standard Specifications for Making Buildings and Facilities Accessible to, and Usable by, the Physically Handicapped, ramps were assessed for flatness based on measuring...
-
3.3.5 Seat Height
The reference points used for measurement can yield quite different results for seat height....
-
Husky 10" Multi-Function Standard Digital Level
The digital display is easy to read. 3 measurement units and audible signals make it suitable for a variety of tasks....
-
Appendix: Revised Annotated Bibliography
standard techniques....
-
APPENDIXES
X1.1.2 PRI precision depends on the interval between adjacent profile elevation measures....
-
StormPave Permeable Clay Pavers Installation Video 2 (Compaction)
Requires the Registered User plan or above. Login! -
C. Training
, including: (a) why such measures are necessary; (b) how the measures must be implemented (e.g., how to install ramps, the placement of mats over (and not in front of) thresholds); and...
-
11B-703.2.5 Character height
Character height measured vertically from the baseline of the character shall be 5/8 inch (15.9 mm) minimum and 2 inches (51 mm) maximum based on the height of the uppercase letter “I”....
-
3. Q: I know I can't give a job applicant a medical exam before a conditional job offer is made. But what about physical agility and physical fitness tests?
A: You can give job applicants tests measuring an applicant's ability to perform job-related tasks or physical fitness tests (tests measuring performance of running, lifting, etc.) before...
-
C. Training
, including: (a) why such measures are necessary; (b) how the measures must be implemented (e.g., how to install ramps, the placement of mats over (and not in front of) thresholds); and...
-
810.2.2 Dimensions
Bus stop boarding and alighting areas shall provide a clear length of 96 inches (2440 mm) minimum, measured perpendicular to the curb or vehicle roadway edge, and a clear width of 60 inches...
-
11B-903.4 Back support
Back support shall be 2½ inches (64 mm) maximum from the rear edge of the seat measured horizontally. [2010 ADA Standards] 903.4 Back Support....
-
LRV Guru App - Demo #1
Just enter the LRV values if you know them -- or -- use a NODE+Chroma hand-held colorimeter to measure for LRV....
-
604.3.1 Size
Clearance around a water closet shall be 60 inches (1525 mm) minimum measured perpendicular from the side wall and 56 inches (1420 mm) minimum measured perpendicular from the rear wall....
-
9. Precision and Bias
9.1 The precision and bias of the computed PRI is limited by the procedures used in making the longitudinal profile measurement. 9.2 For the effects of the precision and bias of the measured...
-
604.3.1 Size
Clearance around a water closet shall be 60 inches (1525 mm) minimum measured perpendicular from the side wall and 56 inches (1420 mm) minimum measured perpendicular from the rear wall....
