9.1 The precision and bias of the computed PRI is limited by the procedures used in making the longitudinal profile measurement. 9.2 For the effects of the precision and bias of the measured...
Search Results "Measuring Technique"
Filters
Commonly Searched Documents
-
9. Precision and Bias
-
604.3.1 Size
Clearance around a water closet shall be 60 inches (1525 mm) minimum measured perpendicular from the side wall and 56 inches (1420 mm) minimum measured perpendicular from the rear wall....
-
Clearance: ADA Standard Section 804.2
Clearances are measured from the furthest projecting face of all opposing base cabinets, counter tops, appliances, or walls, excluding hardware....
-
Station 1-Physical Characteristics
At the first station, the physical characteristics of active participants and their equipment were measured (figure 26)....
-
Selection of Variables
For this survey we suggest variables that fall into five categories: basic body size descriptors reach and functional reach measurements arm and hand strength measurements...
-
C. Election Judge and Poll Worker Training
, including: (a) why such measures are necessary; (b) how the measures must be implemented (e.g., how to install ramps, the placement of mats over (and not in front of) thresholds); and...
-
11B-810.2.2 Dimensions
Bus stop boarding and alighting areas shall provide a clear length of 96 inches (2438 mm) minimum, measured perpendicular to the curb or vehicle roadway edge, and a clear width of 60 inches...
-
11B-703.4.1 Height above finish floor or ground
Tactile characters on signs shall be located 48 inches (1219 mm) minimum above the finish floor or ground surface, measured from the baseline of the lowest Braille cells and 60 inches (1524...
-
11B-810.2.2 Dimensions
Bus stop boarding and alighting areas shall provide a clear length of 96 inches (2438 mm) minimum, measured perpendicular to the curb or vehicle roadway edge, and a clear width of 60 inches...
-
11B-703.4.1 Height above finish floor or ground
Tactile characters on signs shall be located 48 inches (1219 mm) minimum above the finish floor or ground surface, measured from the baseline of the lowest Braille cells and 60 inches (1524...
-
BS8300:2001 Research
It is also not clear what was measured if the chair had no armrests or slanted armrests....
-
§ 36.304(c)(1)
(1) First, a public accommodation should take measures to provide access to a place of public accommodation from public sidewalks, parking, or public transportation....
-
Sec.36.304(c)(1)
(1) First, a public accommodation should take measures to provide access to a place of public accommodation from public sidewalks, parking, or public transportation....
-
405.3 Cross Slope
Cross slope is measured the same way as slope is measured (i.e., the rise over the run)....
-
810.2.2 Dimensions
Bus stop boarding and alighting areas shall provide a clear length of 96 inches (2440 mm) minimum, measured perpendicular to the curb or vehicle roadway edge, and a clear width of 60 inches...
-
405.3 Cross Slope
Cross slope is measured the same way as slope is measured (i.e., the rise over the run)....
-
R308.1.1.1 Dimensions
Boarding and alighting areas shall provide a clear length of 2.4 m (8.0 ft) minimum, measured perpendicular to the curb or street or highway edge, and a clear width of 1.5 m (5.0 ft) minimum...
-
How To Transfer from a Wheelchair to Hospital Bed (Stretcher) with a Sliding Board
Requires the Registered User plan or above. Login! -
Future Work
The devices that are on the market to measure roadway roughness are not applicable to sidewalk and pedestrian surfaces because they either use accelerometers to measure the surface profile...
-
11B-810.2.2 Dimensions
Bus stop boarding and alighting areas shall provide a clear length of 96 inches (2438 mm) minimum, measured perpendicular to the curb or vehicle roadway edge, and a clear width of 60 inches...
-
11B-703.4.1 Height above finish floor or ground
Tactile characters on signs shall be located 48 inches (1219 mm) minimum above the finish floor or ground surface, measured from the baseline of the lowest Braille cells and 60 inches (1524...
-
608.2.1 Transfer Type Shower Compartments
Transfer type shower compartments shall be 36 inches (915 mm) by 36 inches (915 mm) clear inside dimensions measured at the center points of opposing sides and shall have a 36 inch (915...
-
Definitions
that a polling place is compliant with the 2010 ADA Standards for Accessible Design (“2010 Standards”) on Election Day, whether such compliance is achieved through permanent architectural measures...
-
Sec.36.304(c)(3)
(3) Third, a public accommodation should take measures to provide access to restroom facilities....