are not limited to, the following actions – 1) Installing ramps; 2) Making curb cuts in sidewalks and entrances; 3) Repositioning shelves; 4) Rearranging tables...
Search Results "Table Height"
Filters
Commonly Searched Documents
-
11B-101.2 Reserved.
-
GENERAL CONSIDERATIONS FOR TRAFFIC SIGNAL CONTROLLED ROUNDABOUT PEDESTRIAN CROSSINGS
The lower right cell of the table shows the estimated cost for installing signals as depicted in Figure 10 at four legs of a roundabout....
-
Americans with Disabilities Act Amendments Act of 2008
(c) AMENDMENT TO THE TABLE OF CONTENTS....
-
[2010 ADAS] 105.2.2 ASME
The maximum permitted height for operable parts is consistent with 308 of this document. The standard also addresses attendant operation....
-
Railings—Guardrails, Handrails, and Safety
For safety, the International Building Code (IBC), http://www.iccsafe.org, section 1003.2.12 contains requirements for guardrail height and the spacing of rails where there is a drop off...
-
4.1 Introduction
The idea that a control or operable hardware located on a plane in front of the user can be accessible with a forward reach, regardless of the height, is not substantiated by this research...
-
[2010 ADAS] 105.2.2 ASME
The maximum permitted height for operable parts is consistent with 308 of this document. The standard also addresses attendant operation....
-
Whether the definition of ‘‘wheelchair'' includes the Segway® PT. (Section-by-Section Analysis)
In a study of trail and other non-motorized transportation users including EPAMDs, the Federal Highway Administration (FHWA) found that the eye height of individuals using EPAMDs ranged...
-
GE® 30" Drop-In Electric Range JDS28DFWW
30 in Net Weight 116 lb Oven Interior Dimensions (W x H x D) (in.) 24 x 17-1/2 x 18-1/4 Overall Depth 28 1/2 in Overall Height...
-
Symmetry Vertical Platform Lift VPC-SL
Standard Features: 750 lb capacity Speed: 10 FPM with a 1HP, 115V motor Lifting height: up to 168” Steel constructed with electrostatic, powder-coated finish...
-
AJW Architectural Products UG2-Railing UG2X-Y108 108" Concealed Snap Flange, 1.25" Diameter, Peened Grip - Configuration Y
Recommended mounting heights for grab bars are 33" - 36" centerline above finished floor. All mounting of grab bars when possible should have in wall mounting back plates....
-
Hadrian Inc. Corridor Lockers
Quiet Operation The rigid double pan door design and honeycomb core (spanning the complete width and height of the door) make Hadrian lockers the quietest available....
-
Haws Barrier-Free Chilled Dual Wall Mount Fountain H1011.8
mounted on a 14 gauge Type 304 Stainless Steel wall bracket 100% lead-free waterways "Hi-Lo" design allows for twice the users as regular fountains and suits the needs for various user heights...
-
Pilot Rock FSW-30 Campfire Ring
Model FSW-30 Series Campfire Ring features a 30” inside diameter and is available in two side heights of 16-7/8” and 23-3/8”....
-
AJW Architectural Products UG30-Railing UG30X-Y108 108" Concealed Set Screw Flange, 1.5" Diameter, Peened Grip - Configuration Y
Recommended mounting heights for grab bars are 33" - 36" centerline above finished floor. All mounting of grab bars when possible should have in wall mounting back plates....
-
AJW Architectural Products UG3-A Series UG3-A12 12" Concealed Snap Flange, 1.5" Diameter Grab Bar - Configuration A
Recommended mounting heights for grab bars are 33" - 36" centerline above finished floor. All mounting of grab bars when possible should have in wall mounting back plates....
-
AJW Architectural Products UG130-A Series UG130-A12 12" Exposed Flange, 1.5" Diameter Grab Bar - Configuration A
Recommended mounting heights for grab bars are 33" - 36" centerline above finished floor. All mounting of grab bars when possible should have in wall mounting back plates....
-
AJW Architectural Products UG20-Railing UG20X-Y108 108" Concealed Set Screw Flange, 1.25" Diameter, Peened Grip - Configuration Y
Recommended mounting heights for grab bars are 33" - 36" centerline above finished floor. All mounting of grab bars when possible should have in wall mounting back plates....
-
AJW Architectural Products UG2-A Series UG2-A12 12" Concealed Snap Flange, 1.25" Diameter Grab Bar - Configuration A
Recommended mounting heights for grab bars are 33" - 36" centerline above finished floor. All mounting of grab bars when possible should have in wall mounting back plates....
-
Kawneer North America 190/350/500 Standard Entrances
Vertical stiles and top rail are 5" (127); bottom rail measures 6-1/2" (165.1) Results in superior strength for buildings experiencing heavy traffic conditions General Heights...
-
AquaTrek2 ADA Step System
MEETS OR EXCEEDS ADA REQUIREMENTS: No Open Risers 7” Maximum Riser Height 12” Minimum Tread Depth 24” Maximum Width Between Handrails Top Landing...
-
Activar Hiawatha 535/509/536/537 Solid 1 inch Diameter Pulls
• Plate & Pull Combinations • Standard Pulls • Push & Pull Bar Sets • Custom & Unique Pulls • Full Height Pulls • Door Protection Plates & Edges • Auto...
-
AJW Architectural Products UG120-A Series UG120-A12 12" Exposed Flange, 1.25" Diameter Grab Bar - Configuration A
Recommended mounting heights for grab bars are 33" - 36" centerline above finished floor. All mounting of grab bars when possible should have in wall mounting back plates....
-
Kawneer North America Flushline™ Entrances
6.4) or 1" (25.4) infills The aluminum provides a flush appearance while the gasket achieves an architectural look through radiused corners Hardware options allow customization Heights...
