Transfer supports, leg supports and reclining surfaces shall comply with M302.3.
Search Results "Patient in Side-Lying Position"
Filters
Commonly Searched Documents
-
M302.3 Supports
-
M302.2 Transfer Surface
A transfer surface shall be provided and shall comply with M302.2.
-
M302.2 Transfer Surface (Section-by-Section Analysis)
This is an introductory section.
-
M302.3 Supports (Section-by-Section Analysis)
This is an introductory section. An editorial change was made to this section as a result of the change in M302.3.2, described below, to replace the word “stirrups” with the term...
-
M302.2.2 Size
The transfer surface shall be 21 inches (610 mm) wide minimum and 15 inches (381 mm) deep minimum. Advisory M302.2.2 Size. The size requirements in this section apply only to the...
-
M302.2 Transfer Surface
A transfer surface shall be provided and shall comply with M302.2.
-
M302.3 Supports
Transfer supports, armrests, and reclining surfaces shall comply with M302.3.
-
Accessible Patient Rooms
There are certain types of patient rooms, such as those provided in critical or intensive care units where patients who are critically ill are immobile or confined to beds and thus generally...
-
11B-223.1.1.3 Toilet and bathing facilities
Toilet/bathing rooms which are part of patient bedrooms added or altered and required to be accessible shall comply with Section 11B-805.2.4....
-
Facilities Not Specializing in Treating Conditions That Affect Mobility: ADA Standard Section 223.2.1
Section 223.2.1 covers scoping requirements in the current ADA Standards for facilities not specializing in treating conditions that affect mobility.
-
Guldmann Sling Instruction: How to put on the Basic High Comfort Sling on in Bed
Instruction in how to put on the Basic High Comfort sling when the patient is lying in bed....
-
M302.3.3 Head and Back Support
Where the diagnostic equipment is used in a reclined position, head and back support shall be provided and shall comply with M305.5....
-
11B-407.4.8 Car position indicators
Audible and visible car position indicators shall be provided in elevator cars....
-
M305.3.1.3 Vertical Position
The length of the gripping surface on vertical standing supports shall be 18 inches (455 mm) minimum.
-
M305.3.2.2 Vertical Position
The height of the lowest end of the gripping surface on vertical standing supports shall be 34 inches (865 mm) minimum and 37 inches (940 mm) maximum above the standing surface.
-
M305.3.2 Vertical Position
Where the support is vertical, it shall be 18 inches (455 mm) minimum in length and the bottom end of the support shall be 34 inches (865 mm) high minimum and 37 inches (940 mm) high...
-
M302.3.3 Head and Back Support
Where the diagnostic equipment is used in a reclined position, head and back support shall be provided....
-
5.2.3 Transfer Surface Measurement
The transfer surface should be measured from the center-point of each side of the transfer surface....
-
Facilities Specializing in Treating Conditions That Affect Mobility: ADA Standard Section 223.2.2
Section 223.2.2 covers scoping requirements in the current ADA Standards for facilities specializing in treating conditions that affect mobility.
-
Position of Grab Bars: ADA Standard Section 609.4
Section 609.4 covers the current ADA Standards for the position of grab bars.
-
Is additional latch side clearance required on the push side of doors with a forward approach when either a latch or closer (but not both) is provided?
No, latch clearance 12” minimum is required for forward approaches on the push-side of doors equipped with both a closer and a latch....
-
M304.2.1 Slip Resistant
The surface on which the patient stands shall be slip resistant....
-
M304.2 Standing Surface
The surface on which the patient stands shall be slip resistant....
-
M304.2 Standing Surface
Equipment surfaces on which patients stand must comply with M304.2...
