of their hands to record test answers by tape recorder, dictation or computer; Providing extra time to complete a test for people with certain learning disabilities or impaired writing...
Search Results "Check Writing Surface"
-
Some Examples of Alternative Test Formats and Accommodations
-
Passing Spaces: ADA Standard Section 403.5.3
Section 403.5.3 covers the current ADA Standards for passing spaces that are part of an accessible route.
-
11B-605.5.4 Toe Clearance
Partition components at toe clearances shall be smooth without sharp edges or abrasive surfaces....
-
11B-407.4.10 Support rail
Support rails in elevator cabs are used in a different way than handrails along a walking surface such as a ramp or stairway....
-
903.4 Back Support
Back support shall be 42 inches (1065 mm) long minimum and shall extend from a point 2 inches (51 mm) maximum above the seat surface to a point 18 inches (455 mm) minimum above the seat...
-
M301.4.2 Clearance Around Base
The base of the equipment shall provide a clearance 6 inches (150 mm) high minimum measured from the floor and 36 inches (915 mm) deep minimum measured from the edge of the examination surface...
-
4. Do the carpet requirements of Section 302.2 apply to ground level accessible routes within a play area?
Accessible playground surfaces, including turf-like surfaces, must meet the requirements of ASTM F 1951-99....
-
General Accommodations
that emergency services can be contacted; 2) a closing door; 3) supplies that enable individuals to block smoke from entering the room from under the door; 4) a window and something to write...
-
Interactive Illuminated Models
Interactive Illuminated Models Another promising new development expands on the concept of touch sensitive talking models by projecting light onto the model’s 3D surface....
-
Braille Bug
understand the importance of braille for another famous blind person, Helen Keller; learn to recognize braille letters and numbers; describe different ways to read and write...
-
11B-1002.6 Transfer devices for use with amusement rides
Where possible, designers are encouraged to locate the transfer device seat no higher than 17 to 19 inches (430 to 485 mm) above the load and unload surface....
-
IMPLICATION OF A 19-INCH MINIMUM STANDARD FOR THE HIGHEST POINT IN THE LOWEST ADJUSTABLE POSITION
However, shorthand references to 19 inches as the minimum standard as used in this minority report should not be equated with a 19-inch transfer surface height, for two major reasons....
-
Areas for further work
Areas for further work In the process of assisting the various organizations that represent surface materials and professional groups the following issues were identified as parameters...
-
Recommended Objective Test Method and Performance Specifications
firmness and stability on slopes up to 5%, can be used on a wide variety of surface materials, and is suitable for conducting “on trail/on site” tests....
-
M302.4.2 Clearance Around Base
The base of the equipment shall provide a clearance 6 inches (150 mm) high minimum measured from the floor and 36 inches (915 mm) deep minimum measured from the edge of the examination surface...
-
Web Accessibility 101: Using Adobe Edge Inspect
SSB Chief Accessibility Officer Jonathan Avila demonstrates the use of Adobe Edge Inspect for mobile accessibility testing, including how to install Edge Inspect, checking the Document Object...
-
ALIGNMENT OF 19-INCH RECOMMENDATION WITH ACCESS BOARD PROPOSED RULEMAKING
In its proposed rule, the Access Board proposed that the “height of the transfer surface during patient transfer shall be 17 inches (430 mm) minimum and 19 inches (485 mm) maximum measured...
-
11B-407.4.10 Support rail
Support rails in elevator cabs are used in a different way than handrails along a walking surface such as a ramp or stairway. ...
-
Assistive Technology News
He has been writing about disability issues since 1978 and, in 1982, coined the phrase “Assistive Technology,” which has since become the universal term to describe products that benefit...
-
Literature Cited
ASTM F1292 Standard Specification for Impact Attenuation of Surface Systems Under and Around Playground Equipment, ASTM, West Conshohocken,PA 19428 American Society for Testing and Materials...
-
Tread Width
The visible trail surface measured perpendicular to the direction of travel....
-
11B-801.1 Scope
For example, 806 addresses guest rooms in transient lodging facilities while 902 contains the technical specifications for dining surfaces....
-
Key Differences Between Routes
when necessary for drainage —1:20 (5%) 1:20 (5%) 1:12 (8.33%) 200 feet Concrete, asphalt, boards—1:48 (2%) All other surfaces when necessary for...
-
11B-411.2.1.6 Identification of floors served
consoles located on floors with a building entry, including parking and transfer levels, shall be provided with signs complying with Sections 11B-703.2, 11B-703.3, and 11B-703.5 on the surface...