Openings in the clear ground space surface shall not allow the passage of a sphere more than 1/2 inch (13 mm) in diameter. Advisory 1011.2.4 Openings....
Search Results "Check Writing Surface"
-
1011.2.4 Openings
-
Eunice Noell-Waggoner, IES, LC. Value, Contrast and Reflections
Reflective & Transparent Surfaces can be Dangerous Vertical Surfaces (slide 4) Two examples are shown of hazards from reflective and transparent vertical surfaces....
-
III-7.7000 Alterations
are not required in alterations (§4.1.6(1)(g)). 3) There are special less stringent requirements for alterations in many other areas, including sales and service counters (§7.2(1)), check-out...
-
Door King Inc. Proximity Card Readers
Read ranges are not absolute and will vary depending on several factors including where the reader is mounted, the mounting surface and product application....
-
11B-705.3 Product Approval
Only approved DSA-AC detectable warning products and directional surfaces shall be installed as provided in the California Code of Regulations (CCR), Title 24, Part 1, Chapter 5, Articles...
-
Checklist
Commit the plan to writing. Make necessary modifications to the evacuation plan. II. PLAN IMPLEMENTATION. Distribute a copy of the evacuation plan to all employees....
-
5. What will happen after I ask for a reasonable accommodation?
Your employer may ask you to put your request in writing, and to generally describe your condition and how it affects your work....
-
11B-801.1 Scope
For example, Section 11B-806 addresses guest rooms in transient lodging facilities while Section 11B-902 contains the technical specifications for dining surfaces....
-
4. Comparison of Proposed Technical Provisions Applicable to Shared Use Paths and AASHTO Guide
R302.7 Surfaces....
-
Ramp
A walking surface that has a running slope steeper than 1:20....
-
M302.3 Supports
Transfer supports, leg supports and reclining surfaces shall comply with M302.3....
-
11B-903.4 Back support
Back support shall be 48 inches (1219 mm) long minimum and shall extend from a point 2 inches (51 mm) maximum above the seat surface to a point 18 inches (457 mm) minimum above the seat...
-
11B-703.7.1 Finish and contrast
Additional factors affecting the ease with which the text can be distinguished from its background include shadows cast by lighting sources, surface glare, and the uniformity of the text...
-
11B-403.5.3 Passing spaces
Passing spaces shall be either: a space 60 inches (1524 mm) minimum by 60 inches (1524 mm) minimum; or, an intersection of two walking surfaces providing a T-shaped space complying with...
-
11B-705.1.1.3 Color and Contrast
Detectable warning surfaces at transit boarding platform edges, bus stops, hazardous vehicular areas, reflecting pools, and track crossings shall comply with Section 11B-705.1.1.3.1....
-
Passing Spaces [1017.4]
Nominally planar means on the same nominal table surface (same nominal geometric surface plane) and the slopes of the table surface correspond to the running slope and cross slope of the...
-
Handrails
The Board has included a requirement (403.6) that handrails, where provided along walking surfaces, comply with section 505, as discussed above....
-
II. Research Methodology
Research Methodology Beginning in 2010 NCA and the Access Board began strategizing on how to provide a useful resource to trail managers on what natural surface materials were being used...
-
Addendum A: List of Terms
Non-level Transfer- A transfer where the transfer surface is higher or lower than the wheelchair seat to floor height....
-
Tent Pads and Tent Platforms
Accessible surfaces for pitching tents may or may not be at ground level....
-
11B-809.10.5.1 Clear floor space
The edge of the clear floor space shall be flush with the control wall surface....
-
M302.4.1 Clearance in Base
provide a clearance 39 inches (990 mm) wide minimum, 6 inches (150 mm) high minimum measured from the floor, and 36 inches (915 mm) deep minimum measured from the edge of the examination surface...
-
703.4.1 Height Above Finish Floor or Ground
Tactile characters on signs shall be located 48 inches (1220 mm) minimum above the finish floor or ground surface, measured from the baseline of the lowest tactile character and 60 inches...
-
Openings in Beach Access Routes
Openings are gaps in the surface of a beach access route. Gaps include spaces between the planks on a boardwalk and drainage holes in temporary or permanent surfaces....