cover plate finishes available Exposed fastener for easy maintenance Key Specifications Floor/Floor, Floor/Wall Conditions Movement: +/- 50% Joint width...
Search Results "Ramp Width"
Filters
Commonly Searched Documents
-
Inpro Corporation JointMaster® 441 Series-Recessed Mount Expansion Joint
-
Inpro Corporation JointMaster® DR Series Seal Expansion Joint Systems
linear waviness Installation not weather sensitive Utilizes lubricant adhesive (JPR004) Key Specifications: Architectural Compression Seals Joint width...
-
Whitehall Mfg. 4121ADA One-Station Compact Scrub Sink
Product Details Material: Stainless Steel Brand: Scrub-Ware Fixture Width: 36" Accessibility: ADA (if mounted at compliant height) Waste Location...
-
Grainger Anti Ligature Toilet Paper Holder
Specs Item: Toilet Paper Holder Color: Silver Material:Stainless Steel Finish: Stainless Steel Mounting: Wall Capacity: 4" Roll Width...
-
Whitehall Mfg. 4123ADA Three-Station Compact Scrub Sink
This is a three-station unit measuring 108" wide Product Details Material: Stainless Steel Brand: Scrub-Ware Fixture Width: 108" Accessibility: ADA...
-
Whitehall Mfg. 4122ADA Two-Station Compact Scrub Sink
Product Details Material: Stainless Steel Brand: Scrub-Ware Fixture Width: 72" Accessibility: ADA (if mounted at compliant height) Waste Location...
-
1. Injury in Fact
, (4) one street corner that provided only a single curb ramp, (5) errant step stools at three of the City's libraries, (6) three inaccessible pools, and (7) steep paths at one park....
-
Separate Pathways for Pedestrians and Bicyclists
These recommendations include required sight triangles to ensure that bicyclists have the needed yielding distance to avoid conflicts, and additional width around horizontal curves to allow...
-
General Exceptions in FSTAG
For instance, consider a situation where a trail is needed between a stream with endangered aquatic species and a cliff with petroglyphs on it and you can't get the required trail width...
-
M303.2.3 Depth (Section-by-Section Analysis)
(Significant Changes – Width and Depth of Wheelchair Spaces)....
-
How to Measure Transfer Surface Height
The lower wheelchair illustrates a typical diagonal transfer.24 Figure 11: Corner radii of a medical examination table The depth and width are measured along the centerlines of...
-
1134A.7 Water closets
The minimum floor space provided at a water closet shall be 48 inches (1219 mm) in clear width. ...
-
11B-221.2.3.2 Vertical dispersion
Points of entry to bleacher seating may include, but are not limited to, cross aisles, concourses, vomitories, and entrance ramps and stairs....
-
11B-809.2.2 Turning space
Exception: Turning space shall not be required in exterior spaces 30 inches (762 mm) maximum in depth or width. [2010 ADAS] Advisory 809.2.2 Turning Space. ...
-
603.2.3 Door Swing
Additionally, the door swing cannot reduce the required width of an accessible route. Also, avoid violating other building or life safety codes when the door swing is reversed....
-
603.2.3 Door Swing
Additionally, the door swing cannot reduce the required width of an accessible route. Also, avoid violating other building or life safety codes when the door swing is reversed....
-
Guidelines for Requirement 3
For doors within individual dwelling units, the Department has retained, in the final Guidelines, the design specification that a door with a clear opening of at least 32 inches nominal width...
-
603.2.3 Door Swing
Additionally, the door swing cannot reduce the required width of an accessible route. Also, avoid violating other building or life safety codes when the door swing is reversed....
-
Elevated Dune Crossings
The clear width of elevated dune crossings may be narrower than the rest of the beach access route, but must be at least 48 inches (1,220 millimeters)....
-
Recessed Lavatories
Recessed Lavatories Recessing lavatories can provide space for side transfers while allowing a narrower room width....
-
Treads and Risers [4.9.2], Nosings [4.9.3]
Uniformity is important not only between steps but along each step; curved stairs, where the width of each tread varies, do not meet this requirement....
-
F216.13 Trailhead Signs
The technical requirements in 1017.11 require the signs to include information on the length of the trail or trail segment; surface type; typical and minimum tread width; typical and minimum...
-
Station 4-Acceleration
judge whether gaps in oncoming traffic provide sufficient time to cross the roadway safely, based on the speed of oncoming motor vehicles, their own acceleration capabilities, and the width...
-
1016.1 General
The technical requirements address the surface of outdoor recreation access routes, passing spaces, and resting intervals (1016.2); the clear width of outdoor recreation access routes (1016.3...
