provisions for escalators require that at least two flat steps be provided at the entrance and exit of every escalator and that steps on escalators be demarcated by yellow lines 2 inches wide maximum...
Search Results "Feasibility (Technical, Infeasible, Structural, Maximum Extent)"
Filters
Commonly Searched Documents
-
105.2.2 ASME
-
The Brewer Company, LLC
Access Board’s Medical Diagnostic Equipment Technical Advisory Committee discussed the issue of transfer surface heights. Low height options of 17, 18 and 19 inches were discussed....
-
Zurn Industries Trap Protector
Fits 1 1/2 [38] maximum, tubular and semi-cast P traps....
-
Decorative images
This will remove the need for alternative text altogether and will remove the image from the semantic and structural flow of the page....
-
Administrative Requirements
Develop a transition plan if structural changes are necessary for achieving program accessibility....
-
502.3.2 Row, Column, and Headers (Section-by-Section Analysis)
See W3C, Understanding SC 1.3.1, Understanding WCAG 2.0 (Sept. 16, 2014), http://www.w3.org/TR/UNDERSTANDING-WCAG20/content-structure-separation-programmatic.html....
-
Adaptability
This allows structural reinforcement or blocking for later installation of grab bars and removable base cabinetry below lavatories....
-
Transit Facility
The point of the definition is to exempt from TDD requirements open structures, like bus shelters, or facilities which are not used primarily as transportation stops or terminals....
-
II-5.6000 Time periods for achieving program accessibility
If structural changes are needed to achieve program accessibility, they must be made as expeditiously as possible, but in no event later than January 26, 1995....
-
Protruding Objects [1018.9]
Constructed elements on beach access routes and resting intervals must comply with the technical requirements for protruding objects in section 307 of the ABA Standards (figure 31)....
-
B.2.i. - What must an agency do to ensure its' acquisitions of EIT provide "comparable access"?
Unless an exception applies, an agency’s obligation to provide comparable access under Section 508 is satisfied by acquiring EIT that meets the applicable technical provisions in Subparts...
-
§104.23(c)(1)
Departures from particular technical and scoping requirements of UFAS by the use of other methods are permitted where substantially equivalent or greater access to and usability of the building...
-
ADDITIONAL INFORMATION ABOUT THE 2010 STANDARDS
To achieve these objectives, the Department has a robust outreach and technical assistance program designed to assist businesses and State and local governments to understand their obligations...
-
Planning and Designing Outdoor Recreation Facilities for Horses
"Equestrian Design Guidebook for Trails, Trailheads, and Campgrounds," a comprehensive technical resource, details those elements of planning, design, and construction that are specific...
-
F247.3 Trailheads
This section requires at least 20 percent, but not less than one, of each type of outdoor constructed feature provided within trailheads to comply with the applicable technical requirements...
-
II-4.3000 Basic employment requirements
Additional information on employment issues is available in "A Technical Assistance Manual on the Employment Provisions (Title I) of the Americans with Disabilities Act," issued by the EEOC...
-
4.3.4 Industry Considerations in Designing Accessible Imaging Equipment
accuracy must be equivalent across all patients; Patients’ diagnostic needs and thus the clinical applications of the equipment vary widely; Today’s technology has certain technical...
-
Costs
binocular scopes and $3,380 for a dual base telescopes, if viewing scopes provided at viewing areas Trails $40,655 per trail mile, if trail would not otherwise meet the technical...
-
11B-407.4.3 Platform to hoistway clearance
The clearance between the car platform sill and the edge of any hoistway landing shall be 1¼ inch (32 mm) maximum....
-
407.4.3 Platform to Hoistway Clearance
The clearance between the car platform sill and the edge of any hoistway landing shall be 1¼ inch (32 mm) maximum....
-
303.2 Vertical
Changes in level of ¼ inch (6.4 mm) high maximum shall be permitted to be vertical. Figure 303.2 Vertical Change in Level...
-
C101.3 Conventional Industry Tolerances
Dimensions are subject to conventional industry tolerances except where dimensions are stated as a range with specific minimum or maximum end points....
-
E101.3 Conventional Industry Tolerances
Dimensions are subject to conventional industry tolerances except where dimensions are stated as a range with specific minimum or maximum end points....
-
A2
Is the vehicle pull-up area relatively level (1:50 or 2% maximum slope in all directions)? Yes No...
