Spacing between the baselines of separate lines of raised characters within a message shall be 135 percent minimum and 170 percent maximum of the raised character height....
Search Results "Minimum Dimension"
-
11B-703.2.8 Line spacing
-
304.3.1 Circular Space
The turning space shall be a space of 60 inches (1525 mm) diameter minimum. The space shall be permitted to include knee and toe clearance complying with 306....
-
505.5 Clearance
Clearance between handrail gripping surfaces and adjacent surfaces shall be 1½ inches (38 mm) minimum. Figure 505.5 Handrail Clearance...
-
903.5 Height
The top of the bench seat surface shall be 17 inches (430 mm) minimum and 19 inches (485 mm) maximum above the finish floor or ground....
-
703.2.8 Line Spacing
Spacing between the baselines of separate lines of raised characters within a message shall be 135 percent minimum and 170 percent maximum of the raised character height....
-
407.4.5 Illumination
The level of illumination at the car controls, platform, car threshold and car landing sill shall be 5 foot candles (54 lux) minimum....
-
11B-703.5.5 Character height
Minimum character height shall comply with Table 11B-703.5.5....
-
11B-605.5.3 Doors
Section 11B-404 except that if the approach is from the push side of the compartment door, clearance between the door side of the compartment and any obstruction shall be 48 inches (1219 mm) minimum...
-
11B-605.5.3 Doors
Section 11B-404 except that if the approach is from the push side of the compartment door, clearance between the door side of the compartment and any obstruction shall be 48 inches (1219 mm) minimum...
-
11B-703.5.5 Character height
Minimum character height shall comply with Table 11B-703.5.5....
-
Hoyer Advance-E Power Lift
Free Shipping Specifications Weight capacity - 341 lbs Product weight - 69.7 lbs Lifts patient from floor - Yes Max lifting range - 66.5" Minimum...
-
Willoughby Industries UW-1317-HEU Series Contoured High Efficiency Urinal
High Efficiency Urinal shall be washout type requiring 1/8 GPF to 1/2 GPF fl ush valve and 25 psi minimum flushing pressure. Trap shall be fully enclosed and maintain a 3" seal....
-
PEMKO 5" Latching Panic Saddle Threshold No. 2009-PK
Required undercut - minimum of 9/32" and maximum of 15/32" ADA Compliant Concealed fasteners are an option with this profile. Available with added charge....
-
TownSteel ED5500 Grade 1 Panic Rim Device
double door with or without mullion Door Thickness 1-3/4" standard Backset 2-3/4" Device Length 36" for 2'6' to 3' wide openings 48" for 3' to 4' wide openings Stile width 4-1/2" minimum...
-
11B-405.5 Clear width
The clear width of a ramp run shall be 48 inches (1219 mm) minimum. Exceptions: 1. ...
-
11B-604.4 Seats
The seat height of a water closet above the finish floor shall be 17 inches (432 mm) minimum and 19 inches (483 mm) maximum measured to the top of the seat....
-
Common Requirements (R304.5) (Section-by-Section Analysis)
Common Requirements (R304.5) (Section-by-Section Analysis) The clear width of curb ramp runs (excluding flared sides), blended transitions, and turning spaces must be 1.2 meters (4 feet) minimum...
-
11B-604.4 Seats
The seat height of a water closet above the finish floor shall be 17 inches (432 mm) minimum and 19 inches (483 mm) maximum measured to the top of the seat....
-
11B-604.4 Seats
The seat height of a water closet above the finish floor shall be 17 inches (432 mm) minimum and 19 inches (483 mm) maximum measured to the top of the seat....
-
5.8.1.1 Clear Platform Size Recommendation
5.8.1.1 Clear Platform Size Recommendation The Committee recommends a platform size with a minimum clear width of 32 inches and a minimum clear length of 40 inches....
-
T402 Ramps and Bridgeplates
Section T402 has been slightly revised to clarify that the ramps and bridgeplate barriers must be a minimum height of 2 inches, but allows them to be reduced to less than 2 inches when they...
-
M303.2.3.1 Front or Rear Entry
Where wheelchair space entry and exit is provided at only one end (front or rear) the wheelchair space shall be 48 inches (1220 mm) deep minimum....
-
11B-1010.1 Turning space
A circular turning space 60 inches (1524 mm) diameter minimum with slopes not steeper than 1:48 shall be provided at shooting facilities with firing positions....
-
505.7.1 Circular Cross Section
Handrail gripping surfaces with a circular cross section shall have an outside diameter of 1¼ inches (32 mm) minimum and 2 inches (51 mm) maximum....
