The top of the bench seat surface shall be 17 inches (432 mm) minimum and 19 inches (483 mm) maximum above the finish floor or ground....
Search Results "Minimum Dimension"
-
11B-903.5 Height
-
11B-224.8.1 More than 25-bed sleeping rooms
In sleeping rooms with more than 25 beds, a minimum of 5 percent of the beds shall have clear floor space complying with Section 11B-806.2.3....
-
11B-812.6.4 Drive-up
Vehicle spaces serving drive-up EVCS shall be 204 inches (5182 mm) wide minimum and shall not be required to have an adjacent access aisle....
-
11B-703.2.8 Line spacing
Spacing between the baselines of separate lines of raised characters within a message shall be 135 percent minimum and 170 percent maximum of the raised character height....
-
11B-406.5.2 Width
The clear width of curb ramp runs (excluding any flared sides), blended transitions, and turning spaces shall be 48 inches (1219 mm) minimum....
-
TownSteel ED5500 Grade 1 Panic Rim Device
double door with or without mullion Door Thickness 1-3/4" standard Backset 2-3/4" Device Length 36" for 2'6' to 3' wide openings 48" for 3' to 4' wide openings Stile width 4-1/2" minimum...
-
Hoyer Advance-E Power Lift
Free Shipping Specifications Weight capacity - 341 lbs Product weight - 69.7 lbs Lifts patient from floor - Yes Max lifting range - 66.5" Minimum...
-
PEMKO 5" Latching Panic Saddle Threshold No. 2009-PK
Required undercut - minimum of 9/32" and maximum of 15/32" ADA Compliant Concealed fasteners are an option with this profile. Available with added charge....
-
Willoughby Industries UW-1317-HEU Series Contoured High Efficiency Urinal
High Efficiency Urinal shall be washout type requiring 1/8 GPF to 1/2 GPF fl ush valve and 25 psi minimum flushing pressure. Trap shall be fully enclosed and maintain a 3" seal....
-
5.8.1.1 Clear Platform Size Recommendation
5.8.1.1 Clear Platform Size Recommendation The Committee recommends a platform size with a minimum clear width of 32 inches and a minimum clear length of 40 inches....
-
T402 Ramps and Bridgeplates
Section T402 has been slightly revised to clarify that the ramps and bridgeplate barriers must be a minimum height of 2 inches, but allows them to be reduced to less than 2 inches when they...
-
Panda S.81 All Aluminum Multi-Slide Door System
Systems can pocket to left or right, and can stack to left and/or right. 45 and 90 degree configurations are available, as well as panoramic with a radius of minimum 72″....
-
2. Standing Supports
For horizontal standing supports, the Access Board proposed a gripping surface of 4 inches long minimum, the top of which would be required to be located 34 inches minimum and 38 inches...
-
Vertical Alignment-Crest Vertical Curves
Table 20 shows the calculated minimum length of crest vertical curve for each user type, using the values of "A" (the algebraic difference in grades) as described above....
-
M303.2.3.1 Front or Rear Entry
Where wheelchair space entry and exit is provided at only one end (front or rear) the wheelchair space shall be 48 inches (1220 mm) deep minimum....
-
224.3 Beds
In guest rooms having more than 25 beds, 5 percent minimum of the beds shall have clear floor space complying with 806.2.3....
-
11B-1010.1 Turning space
A circular turning space 60 inches (1524 mm) diameter minimum with slopes not steeper than 1:48 shall be provided at shooting facilities with firing positions....
-
505.7.1 Circular Cross Section
Handrail gripping surfaces with a circular cross section shall have an outside diameter of 1¼ inches (32 mm) minimum and 2 inches (51 mm) maximum....
-
1002.6.2 Transfer Height
The height of transfer device seats shall be 14 inches (355 mm) minimum and 24 inches (610 mm) maximum measured from the load and unload surface....
-
11B-902.3 Height
The tops of dining surfaces and work surfaces shall be 28 inches (711 mm) minimum and 34 inches (864 mm) maximum above the finish floor or ground....
-
11B-224.3 Beds
In guest rooms having more than 25 beds, 5 percent minimum of the beds shall have clear floor space complying with Section 11B-806.2.3....
-
703.5.4 Character Proportions
Characters shall be selected from fonts where the width of the uppercase letter "O" is 55 percent minimum and 110 percent maximum of the height of the uppercase letter "I"....
-
1010.1 Turning Space
A circular turning space 60 inches (1525 mm) diameter minimum with slopes not steeper than 1:48 shall be provided at shooting facilities with firing positions....
-
902.3 Height
The tops of dining surfaces and work surfaces shall be 28 inches (710 mm) minimum and 34 inches (865 mm) maximum above the finish floor or ground....
