to make up the difference between the two surfaces, in one direction or the other....
Search Results "Fire-Building Surface"
Filters
Commonly Searched Documents
-
Adjustable Height Range Considered
-
711.4.1.1 Fire-resistance-rated assemblies
Penetrations shall be installed as tested in the approved fire-resistance-rated assembly....
-
711.3.1.1 Fire-resistance-rated assemblies
Penetrations shall be installed as tested in an approved fire-resistance-rated assembly....
-
5.3.2 Transfer Sides Recommendations for M301
the long side of the surface....
-
Regulatory Impact Analysis.
However, this baseline figure does not take into account the fact that, since 1991, various model codes and consensus standards--such as the model International Building Codes ("IBC") published...
-
Alterations: ADA Standard Section 202.3
Section 202.3 covers the most current requirements for alterations in existing building and facilities.
-
Spaces and Elements: ADA Standard Section 206.2.4
Section 206.2.4 covers the scoping requirements in the most current ADA Standards for accessible routes connecting spaces and elements within a building.
-
11B-202 Existing buildings and facilities
SECTION 11B-202 Existing buildings and facilities 11B-202.4 Path of travel requirements in alterations, additions and structural repairs. Exceptions: 7....
-
Simplified Building Kee Access ADA Railings
Kee Access fittings are used to construct ADA and smooth surface railings...
-
Guidelines for Requirement 7
The Guidelines for Requirement 7 present design specifications for providing usable kitchens and bathrooms such that an individual in a wheelchair can maneuver about the space, as...
-
DSA IR 11B-4: DETECTABLE WARNINGS (with revisions issued through Nov. 2011)
Revised 11-18-11 Revised 11-01-07 Issued 01-26-05 See IR 11B-3 References: 2001 California Building Code (CBC), Sections 1117A.4.5, 1127B.5 Item 8, 1133B.8.3, and 1133B.8.5...
-
704.7 Unexposed surface temperature
Where protected openings are not limited by Section 704.8, the limitation on the rise of temperature on the unexposed surface of exterior walls the exterior wall in any story, the total...
-
Clear Ground Space [1011.2]
The technical requirements include specific provisions for the size, location, surface, slope, and openings in the clear ground space....
-
1. Standing Supports
The proposed rule included a provision requiring standing supports on each side of the standing surface and compliance with the technical requirements for standing supports in proposed M305.3...
-
5.4.2.1 Transfer Support Length for Stretchers
5.4.2.1 Transfer Support Length for Stretchers. Transfer supports on stretchers should be a minimum of 15 inches long.
-
Visual Detection of Detectable Warning Materials by Pedestrians with Visual Impairments - Final Report
(Task Order 18 under Project DTFH61-01-C-00049) Authors: James Jenness & Jeremiah Singer May 24, 2006 Prepared for: Federal Highway Administration Washington,...
-
Accessible Parking Space
Accessible Parking Space
-
M301.3.1 Transfer Supports (Section-by-Section Analysis)
The only change in the final rule was to update the cross reference to applicable transfer surfaces to accommodate the changes made to transfer surfaces, described above in Section IV.B.1...
-
Simplified Building Concepts: Assembling the ADA Railing
Simplified Building Concepts: Assembling the ADA Railing...
-
Accessible Courtroom Stations
Other applicable specifications include accessible work surface heights and toe and knee clearance....
-
M301.2.2 Size
The transfer surface shall be 30 inches (760 mm) wide minimum and 15 inches (381mm) deep minimum. Advisory M301.2.2 Size....
-
7(1) Usable kitchens
(1) Usable kitchens. Usable kitchens would meet section 100.205(c)(3)(iv) if:
-
Ramps M303:3.3, 3.3.1, 3.3.2
with drop offs ½ inch or greater would be required to provide edge protection 2 inches high minimum on each side to prevent users from inadvertently travelling off the sides of the ramped surface...
