This is a video demonstrating how to install a single Armor Tile surface-applied tile....
Search Results "Fire-Building Surface"
Filters
Commonly Searched Documents
-
Armor-Tile Tactile Systems Surface Applied Systems Installation Video
-
The Impact of Transfer Setup on the Performance of Independent Transfers: Phase I Final Report
The Impact of Transfer Setup on the Performance of Independent Transfers: Final Report REPORT PREPARED FOR: U.S. ACCESS BOARD, WASHINGTON, DC Authors: Alicia Koontz, PhD,...
-
Requirement 6. Reinforced walls for grab bars.
Section 100.205(c)(3)(iii) requires that covered multifamily dwellings with a building entrance on an accessible route shall be designed and constructed in such a manner that all premises...
-
Appendix to May 23, 2014 Document
Clearances within employee work areas) and 405.8 (Handrails within employee work areas). 2010 Standards without these provisions; Note that HUD is permitting use of Section 215.3 (Fire...
-
Which transition type do users with disabilities prefer?
When a sidewalk slopes more than 2% in the direction of travel and a walk with a maximum 2% cross slope intersects it, which transition segment type provides the safest usability for...
-
B. M301 Diagnostic Equipment Used by Patients in a Supine, Prone, or Side-lying Position and M302 Diagnostic Equipment Used by Patients in a Seated Position
Therefore, the Significant Changes Section addresses the transfer surface and lift compatibility requirements for M301 and M302 together....
-
TotTurf® Synthetic Grass: Play Spaces
Description Tot Turf Play Spaces is a line of natural looking, soft, attenuating turf surfacing perfect for playgrounds....
-
TownSteel ED1400F Grade 1 Mortise Fire Device
ED1400F is ANSI Certified Grade 1 and UL listed for Fire Hardware. Retrofit 98/99 installation requires no additional door prep. ...
-
11B-812.9 Surface marking
EVCS vehicle spaces shall provide surface marking stating “EV CHARGING ONLY” in letters 12 inches (305 mm) high minimum....
-
M305.2.3 Height
During use, the tops of transfer support gripping surfaces shall be 6 inches (150 mm) minimum and 19 inches (485 mm) maximum higher than the top of the associated uncompressed transfer surface...
-
5.4.1 Transfer Support Location for M301 and M302
Provisions require transfer supports be provided for use with the transfer sides and be located within reach of the transfer surface and not obstruct transfer onto the surface when in position...
-
Section G: Ramps
(§405.7.4) G8 If the rise of the ramp is greater than 6", are handrails provided that are between 34" and 38" above the ramp surface?...
-
1.1.3.2 State-regulated buildings, structures, and applications
Applications regulated by the Office of the State Fire Marshal include, but are not limited to, the following in accordance with Section 1.11. 14.1 Buildings or structures used or intended...
-
1.1.3.2 State-regulated buildings, structures, and applications
State-owned buildings, including buildings constructed by the Trustees of the California State University, and to the extent permitted by California laws, buildings designed and constructed...
-
5.4.2 Transfer Support Length for M301 and M302
The purpose of a minimum length is to ensure that there is a minimum gripping surface available to support positioning and repositioning during a transfer....
-
11B-206.2.3 Multi-story buildings and facilities
The following types of privately funded multistory buildings do not require a ramp or elevator above and below the first floor: 1.1 Multi-storied office buildings (other than the...
-
Handrails [§405.8, §505]
Handrail Height and Clearance Handrail Continuity and Extensions Surface requirements and clearances facilitate a power grip along the length of handrails....
-
M305.2.1 Location
Transfer supports shall be located within reach of the transfer surface and shall not obstruct transfer onto or off of the surface when in position....
-
Conclusion
The results from this study along with the results from the first phase should be taken into consideration when designing and building environments for independent wheelchair transfers and...
-
Priority 4: Additional Access - Drinking Fountains, Public Telephones & Fire Alarms
Word Fillable Form (0.7MB) Word Non-Fillable Form (0.6MB) PDF Non-Fillable Form (0.4MB)
-
Outside Surfaces
Subsets of the subjects also traveled over outdoor surfaces around the area at which they were tested with the accelerometers attached to their chairs and rated those surfaces....
-
CHAPTER 5 GENERAL BUILDING HEIGHTS AND AREAS
ETA Editor's Note Sections from California Building Code Chapter 4 that are not adopted by Division of the State Architect - Access Compliance (DSA-AC) have been omitted....
-
5.4.9 Interruptions along Transfer Support Gripping Recommendation for M301 and M302
At the point of connection, these features impede the ability to grasp completely around the cross section of the gripping surface....
-
M305.2 Transfer Supports
M305.2 Transfer Supports M305.2.2 Transfer Supports Structural Strength Proposed requirement: Transfer supports and their connections shall be capable of resisting vertical...
