surface depths of greater than 24 inches....
Search Results "Fire-Building Surface"
Filters
Commonly Searched Documents
-
M305.2.1 Location (Section-by-Section Analysis)
-
5.4.5 Transfer Support Position for Equipment Used in a Supine, Prone, Side-Lying, or Seated Position
The transfer gripping surface should be located within the minimum and maximum heights....
-
1) Historic buildings
1) Historic buildings ADAAG: Contains procedures for buildings eligible for listing in the National Register of Historic Places under the National Historic Preservation Act and for historic...
-
Links
www.fs.fed.us/recreation/programs/accessibility/ Accessibility Guidebook for Ski Areas Operating on Public Lands http://www.fs.fed.us/recreation/programs/accessibility/ Accessible Exterior Surfaces...
-
John Brabyn, Ph.D., Director of Rehabilitation Engineering Research, Center on Low Vision and Blindness (NIDRR), Smith-Kettlewell Eye Research Institute
Building Sight: A handbook of building and interior design solutions to include the needs of visually impaired people....
-
1991 / 1994 ADA Standards - Plan Review Tool - Doors
1991 / 1994 ADA Standards - Plan Review Tool - Doors Click here to view/download the pdf, Page 1 of 2 (256 KB) Click here to view/download the pdf, Page 2 of 2 (272 KB) * *...
-
PRIVATE BUILDING OR FACILITY
[DSA-AC] A place of public accommodation or a commercial building or facility subject to Chapter 1, Section 1.9.1.2. [2010 ADA Standards 106.5] Private Building or Facility....
-
d. Unobstructed Transfer
The MDE NPRM proposed that each transfer side provide unobstructed access to the transfer surface, with an exception to permit temporary obstructions as long as they could be repositioned...
-
DSA IR 11B-9: Accessibility Requirements for Solar Photovoltaic Systems at School Sites
References: California Code of Regulations (CCR) Title 24 Part 1: California Administrative Code Section 4-3335 Part 2: California Building Code, Chapter 2 Definitions...
-
11B-224.7 Housing at a place of education
and clustered sleeping rooms) or on floors containing accessible sleeping rooms with mobility features shall provide turning spaces that comply with Section 11B-809.2.2 and kitchen work surfaces...
-
Sloped Surfaces
Measuring the slope of a ramp, parking space, pedestrian route, or other ground or floor surface is important to identify whether the surface is accessible....
-
5.4.1 Transfer Support Location for Equipment Used in a Supine, Prone, Side-Lying, or Seated Position
Transfer supports should be required on both sides of the transfer surface and be movable or removable so they can be out of the way during transfer....
-
A Wheelchair Rider's Guide to the California Coast
Explore, enjoy, protect. Rolling across the sand in a beach wheelchair Fishing from an accessible pier Hiking an accessible trail or...
-
5.3.1 Permitted Obstructions to Transfer Sides for M301 and M302
provide options to transfer onto the short side and the long side of the surface....
-
5.4.2 Transfer Support Length for Equipment Used in a Supine, Prone, Side-Lying, or Seated Position
The transfer support should be a minimum length of 15 inches positioned so that the transfer support overlaps the minimum depth of the transfer surface by 80%....
-
R201.3 Buildings and Structures
R201.3 Buildings and Structures....
-
1009.4.4 Surface
Surfaces of transfer walls shall not be sharp and shall have rounded edges....
-
1009.5.5 Surface
The surface of the transfer system shall not be sharp and shall have rounded edges....
-
1009.4.4 Surface
Surfaces of transfer walls shall not be sharp and shall have rounded edges....
-
1009.5.5 Surface
The surface of the transfer system shall not be sharp and shall have rounded edges....
-
Same Management or Building
Same Management or Building....
-
Handrails [§504.6, §505]
Handrails [§504.6, §505] Handrails are required on both sides of stairs and must be continuous within the full length of each stair flight. Inside handrails on switchback or...
-
5.4.3 Transfer Support Height for M301 and M302
5.4.3 Transfer Support Height for M301 and M302 Description: Transfer support height applies to the vertical distance that the gripping area of the support is above the transfer surface...
