Figure 305.7.2 Maneuvering Clearance in an Alcove, Parallel Approach...
Search Results "Latch Side Clearance"
Filters
Commonly Searched Documents
-
305.7.2 Parallel Approach
-
305.7.1 Forward Approach
Figure 305.7.1 Maneuvering Clearance in an Alcove, Forward Approach...
-
1002.5.3 Transfer Entry
Where openings are provided for transfer to amusement ride seats, the openings shall provide clearance for transfer from a wheelchair or mobility aid to the amusement ride seat....
-
306.3.2 Maximum Depth
Knee clearance shall extend 25 inches (635 mm) maximum under an element at 9 inches (230 mm) above the finish floor or ground....
-
2. Question: What is the minimum width needed for a level boarding railroad passenger station platform to meet the accessibility requirements of the Americans with Disabilities Act (ADA)?
For a conventional level boarding side passenger platform with a railing or a wall on the platform side opposite the track, the minimum platform width should be the sum of the maximum dimensions...
-
406.2.2 Clear height
While the minimum height is required to be 7'-0" by this section, greater vertical clearance is required at van-accessible parking spaces, standard accessible parking spaces, the vehicular...
-
DORMA 9000 Series Exit Device
Available motorized latch retraction (MLR). Available Finishes The 9000 Series is available in architectural finishes as well as powder coated finishes....
-
11B-305.7.2 Parallel approach
FIGURE 11B-305.7.2 MANEUVERING CLEARANCE IN AN ALCOVE, PARALLEL APPROACH...
-
11B-305.7.1 Forward approach
FIGURE 11B-305.7.1 MANEUVERING CLEARANCE IN AN ALCOVE, FORWARD APPROACH...
-
11B-805.6 Hand washing fixtures, lavatories and sinks
Knee clearance requirement - All accessibility requirements of Section 11B-606 apply to lavatories, sinks and handwashing fixtures required to be accessible. ...
-
Fixed Seating and Tables
At least 27 inches of knee clearance must be provided between the floor and the underside of the table....
-
M305.3 Standing Supports (Section-by-Section Analysis)
in the MDE NPRM preamble on whether the cross section dimensions for gripping surfaces should be applied to standing supports and whether standing supports can provide a 1½ inch minimum clearance...
-
F221.2.3.1 Horizontal Dispersion
In row seating, two wheelchair spaces shall be permitted to be located side-by-side. Advisory F221.2.3.1 Horizontal Dispersion....
-
SafePath: ADA Entry Level Landing Installation Training Video
Modifying vertical rises at door thresholds often requires more than just a ramp, it requires a level-landing, otherwise known as maneuverable clearance area, a firm and stable level surface...
-
Supporting Documents for the Medical Diagnostic Equipment Accessibility Standards Advisory Committee Report
Subcommittee Report - Mammography Subcommittee Report - Stretchers Subcommittee Report - Weight Scales IDeA Center Memo – Transfer Surface Dimensions IDeA Center Memo - Mammography Knee Clearance...
-
Medical Device Manufacturers
• Questions 14 (a) and (b) on height adjustable patient support surfaces; • Question 15 (b) on width of patient support surfaces on equipment used by patients in a supine, prone, or side-lying...
-
1015.2.1 Glazing
Where the glazing provided does not meet the strength and attachment requirements of Section 1607.8, complying guards shall also be located along glazed sides of open-sided walking surfaces...
-
11B-809.10.7.3 Reinforcement for grab bars
Reinforcement for grabs bars shall comply with the following: Where water closets are not placed adjacent to a side wall capable of accommodating a grab bar, the bathroom shall...
-
4. Organization of Technical Criteria
Positions Equipment Designed to Support Equipment Features Addressed in Technical Criteria Types Of Equipment To Which Technical Criteria Applies Supine, prone, or side-lying...
-
T504.1 General
Passenger access routes shall provide clearances that are sufficient to permit passengers using wheelchairs to move between wheelchair spaces and doorways that provide accessible boarding...
-
Robert Judd, CASp, ICC, RAS
As a dedicated ADA Titles II & III specialist, I have worked for both the Federal enforcement and private consulting sides of the law....
-
Do access aisle borders (in blue) have to be painted on all four sides to be considered compliant?
I would say yes as the language in the code is pretty specific using the term "perimeter". I would also say that both of the "end" lines would/could be within the required length.
-
11B-608.2.2 Standard roll-in type shower compartments
Standard roll-in type shower compartments shall be 30 inches (762 mm) wide minimum by 60 inches (1524 mm) deep minimum clear inside dimensions measured at center points of opposing sides...
-
608.5.3 Alternate Roll-In Type Shower Compartments
Where a seat is provided, the controls, faucets, and shower spray unit shall be located on the side wall adjacent to the seat 27 inches (685 mm) maximum from the side wall behind the seat...
