While these technical assistance documents do not address all ADA compliance issues that may arise in emergency shelters, they address a number of the most common access problems....
Search Results "Feasibility (Technical, Infeasible, Structural, Maximum Extent)"
-
F. Emergency Shelter Programs
-
4.28.3(3)
(3) The maximum pulse duration shall be two-tenths of one second (0.2 sec) with a maximum duty cycle of 40 percent....
-
Sec.36.304(a) General
A public accommodation shall remove architectural barriers in existing facilities, including communication barriers that are structural in nature, where such removal is readily achievable...
-
§ 36.304(a) General
A public accommodation shall remove architectural barriers in existing facilities, including communication barriers that are structural in nature, where such removal is readily achievable...
-
4.34.5.5(3) Grab bars
Structural reinforcement or other provisions that will allow installation of grab bars shall be provided in the locations shown in Fig. 49....
-
4.26.3(3)
induced in a fastener or mounting device from the application of 250 lbf (1112N) shall be less than the allowable lateral load of either the fastener or mounting device or the supporting structure...
-
4.1.4(9) INSTITUTIONAL
Institutional occupancy includes, among others, the use of a building or structure, or any portion thereof, in which people have physical or medical treatment or care, or in which the liberty...
-
4.34.5.4(3) Grab bars
Structural reinforcement or other provisions that will allow installation of grab bars shall be provided in the locations shown in Fig. 48....
-
Market Monitoring Report
UCPA recommended that the report should be structured for rapid turnaround after the close of the monitoring period and that successful access solutions be highlighted. Response....
-
7. Diagnostic Imaging Equipment: Accessibility Considerations
As described there and detailed further below, when contemplating improving accessibility, today’s imaging technologies present certain technical constraints, some of which relate to basic...
-
11B-610.3.2 L-shaped seats
The rear edge of an L-shaped seat shall be 2½ inches (64 mm) maximum and the front edge 15 inches (381 mm) minimum and 16 inches (406 mm) maximum from the seat wall....
-
11B-610.3.2 L-shaped seats
The rear edge of an L-shaped seat shall be 2½ inches (64 mm) maximum and the front edge 15 inches (381 mm) minimum and 16 inches (406 mm) maximum from the seat wall....
-
Free-Standing Overhead Lifts
Free-standing, nonpermanent overhead track lifts are a good solution when the provider does not want the lift to be permanently installed or where the existing ceiling structure cannot support...
-
SEC. 513. ALTERNATIVE MEANS OF DISPUTE RESOLUTION. 42 USC 12212
Where appropriate and to the extent authorized by law, the use of alternative means of dispute resolution, including settlement negotiations, conciliation, facilitation, mediation, factfinding...
-
§ 1194.2(c)
procured, maintained, or used by agencies directly or used by a contractor under a contract with an agency which requires the use of such product, or requires the use, to a significant extent...
-
E102.1 Application
The specific editions of the standards listed in Chapter 7 are incorporated by reference into 508 Chapter 2 (Scoping Requirements) and Chapters 3 through 6 to the prescribed extent of each...
-
C102.1 Application
The specific editions of the standards listed in Chapter 7 are incorporated by reference into 255 Chapter 2 (Scoping Requirements) and Chapters 3 through 6 to the prescribed extent of each...
-
E202.6 Undue Burden or Fundamental Alteration
to requirements in the Revised 508 Standards would impose an undue burden or would result in a fundamental alteration in the nature of the ICT, conformance shall be required only to the extent...
-
E202.5.1 Basis for a Determination of Undue Burden
In determining whether conformance to requirements in the 508 Standards would impose an undue burden on the agency, the agency shall consider the extent to which conformance would impose...
-
§ 38.111(a)(1)
Compliance with §38.125 of this part shall be required only to the extent necessary to meet the requirements of paragraph (d) of this section....
-
F238.2.1 Teeing Grounds
forward teeing ground shall not be required to be one of the teeing grounds on a hole designed and constructed so that a golf car can enter and exit the teeing ground where compliance is not feasible...
-
238.2.1 Teeing Grounds
forward teeing ground shall not be required to be one of the teeing grounds on a hole designed and constructed so that a golf car can enter and exit the teeing ground where compliance is not feasible...
-
11B-238.2.1 Teeing grounds
forward teeing ground shall not be required to be one of the teeing grounds on a hole designed and constructed so that a golf car can enter and exit the teeing ground where compliance is not feasible...
-
Access to Performing Areas [4.33.5]
Aisles with slopes no steeper than 1:12 are often feasible in small and medium size assembly areas and permit accessible routes that coincide with general routes....