Is at least one wide toilet stall provided with an out swinging door, side and rear grab bars, and clear space next to the toilet?...
Search Results "Pull Side"
Commonly Searched Documents
-
H15
-
11B-608.3.3 Alternate roll-in type shower compartments
In alternate roll-in type shower compartments, grab bars shall be provided on the back wall and the side wall farthest from the compartment entry....
-
Clear Floor Space [4.27.2]
Clear Floor Space [4.27.2] Clear floor space for a forward or side approach is required at controls, dispensers, receptacles, and other operable equipment as specified in 4.2; those recessed...
-
Size and Clearances [4.21.2]
Recommendation: Twelve inches of additional clear floor space at the seat will facilitate side transfers....
-
Door Pressure Gauge
Door Pressure Gauge This Door Pressure Gauge, available from Evan Terry Associates, measures forces from 0-35 pounds on one side and 0-16 kilograms on the other....
-
Maneuvering Clearances [§404.2.4]
Clearance beyond the latch side is not required at entry doors to hospital patient rooms. ...
-
M305 Supports
The technical criteria for transfer supports are discussed under M301 Diagnostic Equipment Used by Patients in Supine, Prone, or Side-Lying Position and M302 Diagnostic Equipment Used by...
-
11B-804.2.1 Pass through kitchen
In pass through kitchens where counters, appliances or cabinets are on two opposing sides, or where counters, appliances or cabinets are opposite a parallel wall, clearance between all opposing...
-
11B-602.3 Operable parts
The flow of water shall be activated by a manually operated system that is front mounted or side mounted and located within 6 inches (152 mm) of the front edge of the fountain or an automatic...
-
1132A.1 Primary entry doors and required exit doors
The requirements of Sections 1126A.3 shall apply to maneuvering clearances at the side of the door exposed to common or public use spaces (e.g., entry or exit doors which open from the covered...
-
1132A.1 Primary entry doors and required exit doors
The requirements of Sections 1126A.3 shall apply to maneuvering clearances at the side of the door exposed to common or public use spaces (e.g., entry or exit doors which open from the covered...
-
11B-804.2.1 Pass through kitchen
In pass through kitchens where counters, appliances or cabinets are on two opposing sides, or where counters, appliances or cabinets are opposite a parallel wall, clearance between all opposing...
-
11. Q: If the person uses sign language, what kinds of communication will require an interpreter?
The driver, who is deaf, is pulled over and issued a noncriminal citation....
-
11B-1008.4.2 Clear floor or ground space
These dimensions apply to either forward or side reaches. The reach ranges are appropriate for use with those play components that children seated in wheelchairs may access and reach....
-
Measuring Techniques
Zone 3 specifies that the inertia reel be unlocked and the shoulders and torso permitted to move forward and to the sides as necessary for maximum reaches....
-
Examples of alternative ways to serve a customer when barrier removal is not feasible are:
Examples of alternative ways to serve a customer when barrier removal is not feasible are: At a dry cleaner's, providing curb-side service for a customer dropping off or picking up...
-
Alternate Roll-in Showers
The revised language clarifies the location of the entry at the end of the long side of the compartment (608.2.3)....
-
10. Can a transfer platform be an irregular shape as long as it incorporates the minimum rectangle of 14 by 24 inches?
The 24 inch side of the transfer platform must be free from obstructions to allow a person to transfer....
-
Clear Floor Space
Designers may decide which location is best suited for transfer on a particular ride.Because people transfer in different ways, providing additional space both in front of and to the side...
-
T704.3.2 Automated Route Identification Announcements
Signs displaying route identification information shall be provided on the front and boarding sides of non-rail vehicles. Signs shall comply with T702....
-
407.8 Reach Height and Depth
of operable part of stationary ICT shall be at a height conforming to 407.8.2 or 407.8.3 according to its position established by the vertical reference plane specified in 407.8.1 for a side...
-
404.2.5 Thresholds
EXCEPTION: Existing or altered thresholds 3/4 inch (19 mm) high maximum that have a beveled edge on each side with a slope not steeper than 1:2 shall not be required to comply with 404.2.5...
-
3. Protruding Objects
Is the voting area free of objects that protrude from the side more than 4 inches into the route with the bottom of the object more than 27 inches above the floor?...
-
4.10.12(3)
All floor buttons shall be no higher than 54 in (1370 mm) above the finish floor for side approach and 48 in (1220 mm) for front approach....