The seat shall be 16 inches (405 mm) wide minimum....
Search Results "Minimum Dimension"
-
1009.2.5 Seat Width
-
1009.2.5 Seat Width
The seat shall be 16 inches (405 mm) wide minimum....
-
11B-411.2.1.2.4.3 Duration
Elevator assignment characters shall be displayed for a minimum of 5 seconds....
-
12185(b) Contents
(b) Contents The study shall include, at a minimum, an analysis of the following:...
-
4.8.3 Clear Width
The minimum clear width of a ramp shall be 36 in (915 mm)....
-
4.1.3 Accessible Buildings: New Construction
Accessible buildings and facilities shall meet the following minimum requirements:...
-
4.8.3 CLEAR WIDTH
The minimum clear width of a ramp shall be 36 in (915 mm)....
-
4.1.2 ACCESSIBLE BUILDINGS: NEW CONSTRUCTION
Accessible buildings and facilities shall meet the following minimum requirements:...
-
1016.8.1 Length
This section requires resting intervals to be 60 inches long minimum....
-
1017.8.1 Length
This section requires resting intervals to be 60 inches long minimum....
-
11B-411.2.1.2.4.3 Duration
Elevator assignment characters shall be displayed for a minimum of 5 seconds....
-
11B-1009.2.5 Seat width
The seat shall be 16 inches (406 mm) wide minimum....
-
11B-1009.2.5 Seat width
The seat shall be 16 inches (406 mm) wide minimum....
-
11B-411.2.1.2.4.3 Duration
Elevator assignment characters shall be displayed for a minimum of 5 seconds....
-
American Specialties 9012 Surface Mounted Baby Changing Station
Using mounting dimension on cut sheet diagram will result in knee clearance under the unloaded bed tray, after installation, of 27" to 27-3/8" [686 to 695] and the rim of the changing table...
-
607.4.2.1 Back Wall
Two grab bars shall be installed on the back wall, one located in accordance with 609.4 and other located 8 inches (205 mm) minimum and 10 inches (255 mm) maximum above the rim of the bathtub...
-
11B-1009.2.3 Clear deck space
The space shall be 36 inches (914 mm) wide minimum and shall extend forward 48 inches (1219 mm) minimum from a line located 12 inches (305 mm) behind the rear edge of the seat....
-
11B-607.4.2.1 Back wall
Two grab bars shall be installed on the back wall, one located in accordance with Section 11B-609.4 and the other located 8 inches (203 mm) minimum and 10 inches (254 mm) maximum above the...
-
11B-407.2.2.2 Visible signals
Visible signal fixtures shall be centered at 72 inches (1829 mm) minimum above the finish floor or ground....
-
M302.4.2 Clearance Around Base
The base of the diagnostic equipment shall provide a clearance 6 inches (150 mm) high minimum measured from the floor and 36 inches (915 mm) deep minimum measured from the edge of the examination...
-
M305.2.3 Height
During use, the tops of transfer support gripping surfaces shall be 6 inches (150 mm) minimum and 19 inches (485 mm) maximum higher than the top of the associated uncompressed transfer surface...
-
M301.4.2 Clearance Around Base
The base of diagnostic equipment shall provide a clearance 6 inches (150 mm) high minimum measured from the floor and 36 inches (915 mm) deep minimum measured from the edge of the examination...
-
1009.4.1 Clear Deck Space
A clear deck space of 60 inches (1525 mm) minimum by 60 inches (1525 mm) minimum with a slope not steeper than 1:48 shall be provided at the base of the transfer wall....
-
307.4 Vertical Clearance
Vertical clearance shall be 80 inches (2030 mm) high minimum. Guardrails or other barriers shall be provided where the vertical clearance is less than 80 inches (2030 mm) high....
