Swinging door and gate surfaces within 10 inches (255 mm) of the finish floor or ground measured vertically shall have a smooth surface on the push side extending the full width of the door...
Search Results "Vertical Clearance"
-
404.2.10 Door and Gate Surfaces
-
206.2.4 Spaces and Elements
Exceptions 1 – 3 are preempted by Florida vertical accessibility requirements of s.553.509, F.S., as incorporated in section 201.1.1....
-
11B-504.5 Nosings
Risers shall be permitted to slope under the tread at an angle of 30 degrees maximum from vertical....
-
11B-504.5 Nosings
Risers shall be permitted to slope under the tread at an angle of 30 degrees maximum from vertical....
-
A4.2.4 CLEAR FLOOR OR GROUND SPACE FOR WHEELCHAIRS
The space requirements in this standard are based upon maneuvering clearances that will accommodate most larger wheelchairs. Fig....
-
206.2.3 Multi-Story Buildings and Facilities
Exceptions 1 – 7 are preempted by Florida vertical accessibility requirements of s. 553.509, F.S., as incorporated in section 201.1.1....
-
Hager Companies Rectangular Wrought Door Pull 2
Rectangular Wrought Door Pull Materials: - Aluminum, brass, bronze, stainless steel Accessible: - 2-1/2" (64 mm) Clearance available on special order....
-
Doors: ADA Standard Section 604.8.1.2
Section 604.8.1.2 covers the current ADA Standards for wheelchair accessible compartment doors.
-
PDQ 4200 Series Exit Device Door Hardware
The American Eagle 4200 Series is a rim or surface vertical rod exit device....
-
Corbin Russwin Inc. ED7000 Series Narrow Stile Crossbar Exit Device
The ED7000 Series are available as Rim, Surface Vertical Rod, Mortise and Concealed Vertical Rod devices. ...
-
Husky 24" Line Generator Digital Laser Level
This level may use indoors or out for horizontal (level), vertical (plumb) and square alignment projects....
-
504.5 Nosings
Risers shall be permitted to slope under the tread at an angle of 30 degrees maximum from vertical....
-
703.2.5 Character Height
Character height measured vertically from the baseline of the character shall be 5/8 inch (16 mm) minimum and 2 inches (51 mm) maximum based on the height of the uppercase letter "I"....
-
7.4.5.1 Size
Vertical alignment at the intersection of the trails that form the T-shaped space shall be nominally level....
-
Spout Location [4.15.3]
The trajectory of water flow must be vertically "parallel" or "nearly parallel" to the face of the unit....
-
§ 38.73(d)(1) Requirements
Vertical alignment may be accomplished by vehicle air suspension, automatic ramps or lifts, or any combination....
-
11B-703.2.5 Character height
Character height measured vertically from the baseline of the character shall be 5/8 inch (15.9 mm) minimum and 2 inches (51 mm) maximum based on the height of the uppercase letter “I”....
-
504.5 Nosings
Risers shall be permitted to slope under the tread at an angle of 30 degrees maximum from vertical....
-
1008.3.2.3 Transfer Supports
Some examples of supports include a rope loop, a loop type handle, a slot in the edge of a flat horizontal or vertical member, poles or bars, or D rings on the corner posts....
-
703.2.5 Character Height
Character height measured vertically from the baseline of the character shall be 5/8 inch (16 mm) minimum and 2 inches (51 mm) maximum based on the height of the uppercase letter "I"....
-
Paperwork Reduction Act
This rule does not contain any paperwork or recordkeeping requirements and does not require clearance under the PRA....
-
Hager Companies Modified Half Round Wrought Door Pull 1
Modified Half Round Wrought Door Pull Materials: - Aluminum, brass, bronze, stainless steel Accessible: - 2-1/2" (64 mm) Clearance available on special order....
-
11B-805.6 Hand washing fixtures, lavatories and sinks
Knee clearance requirement - All accessibility requirements of Section 11B-606 apply to lavatories, sinks and handwashing fixtures required to be accessible....
-
11B-805.6 Hand washing fixtures, lavatories and sinks
Knee clearance requirement - All accessibility requirements of Section 11B-606 apply to lavatories, sinks and handwashing fixtures required to be accessible....
