Clearance of 36 inches (914 mm) wide minimum by 48 inches (1219 mm) long minimum measured from the control wall shall be provided....
Search Results "Vertical Clearance"
Filters
Commonly Searched Documents
-
11B-608.2.1 Transfer type shower compartments
-
Bobrick TrimLineSeries ADA Surface-Mounted Hand Dryer B-7128.115V
Durable, 22-gauge galvanized steel with exposed surface, type 304 satin-finish stainless steel cover having #4 satin-finish vertical grain with black plastic trim, automatic sensor, dual...
-
Trail Slopes
Slopes are often described as a ratio of vertical distance to horizontal distance, or rise to run (figure 130)....
-
11B-608.2.3 Alternate roll-in type shower compartments
FIGURE 11B-608.2.3 ALTERNATE ROLL-IN TYPE SHOWER COMPARTMENT SIZE AND CLEARANCE...
-
1009.4.1 Clear Deck Space
Where two grab bars are provided, the clear deck space shall be centered on the clearance between the grab bars....
-
Post-Mounted Objects [§307.3]
The 12” limit also applies to the clearance between multiple posts (excluding the sloping portions of handrails)....
-
Clear Floor Space [§309.2]
If clear floor space is obstructed on both sides more than half the minimum required depth, a wider clearance (36” min.) is required for maneuvering and sway....
-
Handrails [ADA Standards §504.6, §505]
Handrails [ADA Standards §504.6, §505] Specifications in the ADA Standards for handrail surfaces and clearances facilitate a power grip along the handrail length....
-
11B-1009.4.1 Clear deck space
Where two grab bars are provided, the clear deck space shall be centered on the clearance between the grab bars....
-
§ 38.125(a)(1) General
., lift, ramp or bridge plate) complying with either paragraph (b) or (c) of this section and sufficient clearances to permit a wheelchair or other mobility aid user to reach a seating location...
-
11B-1009.4.1 Clear deck space
Where two grab bars are provided, the clear deck space shall be centered on the clearance between the grab bars....
-
SDC S6000 Spectra Exit Devices
The new SDC S6000 Spectra™ series panic and fire rated exit devices are available in rim mount, mortise and vertical rod configurations and are UL listed and ANSI A156.3 Grade 1 compliant...
-
Kawneer North America 190/350/500 Standard Entrances
The 190 Narrow Stile Entrance Is engineered for moderate traffic in applications such as stores, offices and apartment buildings Vertical stile measures 2-1/8" (54); top rail 2-1...
-
11B-303.5 Warning curbs
Abrupt changes in level exceeding 4 inches (102 mm) in a vertical dimension between walks, sidewalks or other pedestrian ways and adjacent surfaces or features shall be identified by warning...
-
11B-303.3 Beveled
A change in level of ½ inch (13 mm) is permitted to be ¼ inch (6.4 mm) vertical plus ¼ inch (6.4 mm) beveled....
-
F206.3 Location
Additionally, accessible vertical interior circulation must be in the same area as stairs and escalators, not isolated in the back of the facility....
-
Handrail Extensions
Other specifications regarding vertical supports may be addressed in other building codes....
-
405.9 Edge Protection
Edge protection shall not be required on the sides of ramp landings having a vertical drop-off of ½ inch (13 mm) maximum within 10 inches (255 mm) horizontally of the minimum landing area...
-
Transfer Height
If multiple transfers are necessary to reach the amusement ride seat, it is recommended that each vertical transfer not exceed 8 inches....
-
405.9 Edge Protection
Edge protection shall not be required on the sides of ramp landings having a vertical drop-off of ½ inch (13 mm) maximum within 10 inches (255 mm) horizontally of the minimum landing area...
-
Handrails
[ADA Stds. 4.9] Yes __ No __ N/A __ Comments: ___________________________________________ ...are the handrails continuously grippable, without interruption by vertical supports, newel...
-
407.2.2.2 Visible Signals
The visible signal elements shall be 2½ inches (64 mm) minimum measured along the vertical centerline of the element....
-
303.3 Beveled
A change in level of 1/2 inch (13 mm) is permitted to be ¼ inch (6.4 mm) vertical plus ¼ inch (6.4 mm) beveled....
