The bottom extension is especially important in providing this support until one is fully vertical....
Search Results "Vertical Clearance"
-
Extensions
-
§ 38.53(d)(1) Requirements
Vertical alignment may be accomplished by vehicle air suspension or other suitable means of meeting the requirement....
-
11B-703.6.1 Pictogram field
The 6-inch vertical dimension applies to the field, not the symbol. The symbol may be smaller than the field....
-
§ 38.29(e)
(e) For vehicles in excess of 22 feet in length with front-door lifts or ramps, vertical stanchions immediately behind the driver shall either terminate at the lower edge of the aisle-facing...
-
11B-608.7 Thresholds
In transfer type shower compartments, thresholds ½ inch (12.7 mm) high maximum shall be beveled, rounded, or vertical....
-
11B-404.2.10 Door and gate surfaces
Swinging door and gate surfaces within 10 inches (254 mm) of the finish floor or ground measured vertically shall have a smooth surface on the push side extending the full width of the door...
-
404.2.10 Door and Gate Surfaces
Swinging door and gate surfaces within 10 inches (255 mm) of the finish floor or ground measured vertically shall have a smooth surface on the push side extending the full width of the door...
-
Design Criteria for the Transfer Station
Seat width ranges for platform 1 and 2 Adjustable between 18” and 30” Seat depth for platform 1 and 2 Fixed at 16” Vertical...
-
223.1 General
Florida vertical accessibility requirements of s.553.509, F.S., as incorporated in section 201.1.1 require vertical access to all levels of facilities....
-
11B-404.2.10 Door and gate surfaces
Swinging door and gate surfaces within 10 inches (254 mm) of the finish floor or ground measured vertically shall have a smooth surface on the push side extending the full width of the door...
-
11B-410.8 Restriction sign
For lifts with a signed installation contract before May 1, 2008: CCR, Title 8, Section 3094 provides safety regulations for Vertical Platform (Wheelchair) Lifts....
-
11B-404.2.10 Door and gate surfaces
Swinging door and gate surfaces within 10 inches (254 mm) of the finish floor or ground measured vertically shall have a smooth surface on the push side extending the full width of the door...
-
(C) NYCT’s interpretation of the ADA and DOT’s implementing regulations is too narrow.
To address another argument presented by NYCT,1 the ADA Accessibility Guidelines (ADAAG) do not, as NYCT contends, limit the requirement that “a means of accessible vertical access” be provided...
-
4.2.5* Forward Reach
If the high forward reach is over an obstruction, reach and clearances shall be as shown in Fig. 5(b)....
-
4.34.5.3 LAVATORY, MIRRORS, AND MEDICINE CABINETS
(2) If a cabinet is provided under the lavatory in adaptable bathrooms, then it shall be removable to provide the clearances specified in 4.22.6....
-
Are doors or gates to employee work areas required to comply?
Entry doors or gates to employee work areas are required to meet applicable requirements, including those for maneuvering clearance, on the exterior, but not the interior....
-
IDEA Center
A shelf location closest to the highest vertical free reach was used to measure high reach; mid level was set at or near the shoulder and the shelf for the lower reach was set at the MCP5...
-
Don-Jo Mfg., Inc. Pull Plate 7011
Number 7011 Dimensions 3-1/2" x 15" Ansi J405 Ctc 5-1/2" Diameter 5/8" Projection 2" Clearance...
-
Bobrick MatrixSeries Seat-Cover Dispenser B-5221
Allow 5" (125mm) minimum clearance from bottom of dispenser to top of any horizontal projection for filling dispenser from below unit....
-
11B-407.4.10.1 Location
Clearance between support rails and adjacent surfaces shall be 1½ inches (38 mm) minimum....
-
1.17 Unobstructed view
purposes of this Consent Order, shall mean and refer to a view to the screen that is not blocked or interfered with by any seats, railings, or other objects and is configured to have visual clearance...
-
7. Lavatory
Is the lavatory (wash basin) in each accessible guestroom bathroom no more than 34" high with at least 29" high clearance under the front edge to allow persons who use wheelchairs to pull...
-
11B-604.8.1.1.1 Maneuvering space with in-swinging door
In a wheelchair accessible compartment with an in-swinging door, a minimum 60 inches (1524 mm) wide by 36 inches (914 mm) deep maneuvering space shall be provided in front of the clearance...
-
11B-407.4.10.1 Location
Clearance between support rails and adjacent surfaces shall be 1½ inches (38 mm) minimum....
