The grab bar reinforcement shall be a minimum of 6 inches (152.4 mm) nominal in height. The backing shall be a minimum of 40 inches (1016 mm) in length....
Search Results "Minimum Dimension"
-
1134A.7, Item 2
-
Recessed Lavatories
The rear grab bar determines the minimum distance of the lavatory from the water closet....
-
1134A.7, Item 1
The minimum floor space provided at a water closet shall be 48 inches (1219 mm) in clear width....
-
1134A.7, Item 2
The grab bar reinforcement shall be a minimum of 6 inches (152.4 mm) nominal in height. The backing shall be a minimum of 40 inches (1016 mm) in length....
-
11B-809.10.5.2 Reinforcement for grab bars
At the control end wall and head end wall, between 30 inches (762 mm) maximum to 38 inches (965 mm) minimum above the finish floor, extending 28 inches (711 mm) minimum from the front edge...
-
11B-604.2 Location
The centerline of the water closet shall be 17 inches (432 mm) minimum to 18 inches (457 mm) maximum from the side wall or partition, except that the water closet shall be 17 inches (432...
-
1007.2 Accessible Routes
Where accessible routes intersect playing surfaces of holes, a 1 inch (25 mm) maximum curb shall be permitted for a width of 32 inches (815 mm) minimum. 3....
-
Ground Level Requirements Based on Elevated Play Components
Table 240.2.1.2 Number of elevated play components provided Minimum number of ground-level play components required to be on accessible route Minimum number of different...
-
M303.2.3 Depth (Section-by-Section Analysis)
spaces that can only be entered from the side, 60 inches deep minimum....
-
11B-703.8.4 Character height
The uppercase letter “I” of the font shall have a minimum height complying with Table 11B-703.8.4....
-
11B-810.5.3 Platform and vehicle floor coordination
Low-level platforms shall be 8 inches (203 mm) minimum above top of rail....
-
11B-810.5.3 Platform and vehicle floor coordination
Low-level platforms shall be 8 inches (203 mm) minimum above top of rail....
-
11B-703.8.4 Character height
The uppercase letter “I” of the font shall have a minimum height complying with Table 11B-703.8.4....
-
11B-224.2 Guest rooms with mobility features
TABLE 11B-224.2 GUEST ROOMS WITH MOBILITY FEATURES TOTAL NUMBER OF GUEST ROOMS PROVIDED MINIMUM NUMBER OF REQUIRED ROOMS WITHOUT ROLL-IN SHOWERS1 MINIMUM...
-
Width and Length
Width and Length Transfer walls must be a minimum of 12 inches wide to a maximum of 16 inches wide....
-
703.2.5 Character Height
Character height measured vertically from the baseline of the character shall be 5/8 inch (16 mm) minimum and 2 inches (51 mm) maximum based on the height of the uppercase letter “I”....
-
4.7.7 Water Spouts
Water spouts shall be located in the space so that the water spout is 11 inches (280 mm) minimum and 12 inches (305 mm) maximum from the rear center of the long side of the clear floor or...
-
4.34.6.4(4)
The knee space shall have a minimum clear width of 30 in (760 mm) and a minimum clear depth of 19 in (485 mm)....
-
1009.7.4 Stairways
Stairways that are part of the means of egress for the exterior area for assisted rescue shall provide a minimum clear width of 48 inches (1220 mm) between handrails....
-
607.2 Clearance
Clearance in front of bathtubs shall extend the length of the bathtub and shall be 30 inches (760 mm) wide minimum....
-
802.1.3 Depth
Where a wheelchair space can be entered from the front or rear, the wheelchair space shall be 48 inches (1220 mm) deep minimum....
-
Delta Single Handle Basin Faucet 570LF-WFHDF
set by Americans with Disabilities Act (ADA) 1.50 gpm @ 60 psi, 5.7 L/min @ 414 kPa Single hole installation Standard spout swivels 360¿ Assembled dimensions...
-
Omnia Industries Inc. Interior Modern Lever Latchset with Square Rose - Stainless Steel No.25S
Interior Modern Lever Latchset with Square Rose - Stainless Steel Dimensions: 2-5/8" Projection x 5-3/8" Length, 5/8" Lever Diameter Rose: 2-3/8" Square x 7/16" Projection Finishes...
