The clearance between the car platform and the edge of any landing sill shall be 1½ inch (38 mm) maximum....
Search Results "Feasibility (Technical, Infeasible, Structural, Maximum Extent)"
-
11B-409.4.3 Platform to hoistway clearance
-
Stroke Thickness: ADA Standard Section 703.5.7
Stroke thickness of the uppercase letter “I” shall be 10 percent minimum and 30 percent maximum of the height of the character....
-
Platform to Hoistway Clearance: ADA Standard Section 409.4.3
Section 409.4.2 covers the ADA Standards for the required clearance between the car platform and the hoistway landing in private residence elevators.
-
Explore Online Entertainment
When a familiar gaming platform becomes difficult to access, the cause can range from maintenance to regional or technical issues....
-
C. Compliance issues
What technical assistance should the Department make available to public entities and public accommodations to assist them with complying with this rule? Question 7....
-
Introduction
Just a little bit about myself: I am director of the Office of Technical and Information Services with the U.S. Access Board....
-
11B-234.1 General
In those situations, these requirements are to be applied to the extent possible....
-
11B-234.1 General
In those situations, these requirements are to be applied to the extent possible....
-
11B-234.1 General
In those situations, these requirements are to be applied to the extent possible....
-
1. Application of Functional Performance Criteria: 508 Standards
Agencies should first look to the provisions in Subpart B [technical provisions] to determine if there are specific technical provisions that apply to the [ICT] need they are seeking to...
-
Section 1630.2(j)(1)(i) Broad Construction; not a Demanding Standard
(i) Broad Construction; not a Demanding Standard Section 1630.2(j)(1)(i) states: “The term ‘substantially limits’ shall be construed broadly in favor of expansive coverage, to the maximum...
-
1. Under Title II, what must public school districts do to provide effective communication to students with hearing, vision, or speech disabilities?
However, the school still has an obligation to provide, to the maximum extent possible, an effective auxiliary aid or service.22 These concepts are discussed in greater detail below....
-
Sec.36.304(g)(3)
(3) This section does not apply to rolling stock and other conveyances to the extent that Sec.36.310 applies to rolling stock and other conveyances....
-
Accessible Routes: ADA Standard Section 1007.2
Where accessible routes intersect playing surfaces of holes, a 1 inch (25 mm) maximum curb shall be permitted for a width of 32 inches (815 mm) minimum. 3....
-
11B-504.5 Nosings
The radius of curvature at the leading edge of the tread shall be ½ inch (12.7 mm) maximum....
-
11B-504.5 Nosings
The radius of curvature at the leading edge of the tread shall be ½ inch (12.7 mm) maximum....
-
11B-809.10.5.2 Reinforcement for grab bars
At the control end wall and head end wall, between 30 inches (762 mm) maximum to 38 inches (965 mm) minimum above the finish floor, extending 28 inches (711 mm) minimum from the front edge...
-
11B-809.10.5.2 Reinforcement for grab bars
At the control end wall and head end wall, between 30 inches (762 mm) maximum to 38 inches (965 mm) minimum above the finish floor, extending 28 inches (711 mm) minimum from the front edge...
-
Summary of ADAAG (Preamble, Section-by-Section Analysis)
SUMMARY OF ADAAG This section of the preamble summarizes the structure of ADAAG, and highlights the more important portions....
-
Security Glazing
A commenter pointed out that the provision for solid partitions or security glazing in visiting areas should be revised to be more consistent with the technical provision it references,...
-
Toilet Compartment Access
Where located in the front partition, the door opening shall be 4 inches (100 mm) maximum from the side wall or partition farthest from the water closet....
-
11B-609.4 Position of grab bars
Grab bars shall be installed in a horizontal position, 33 inches (838 mm) minimum and 36 inches (914 mm) maximum above the finish floor measured to the top of the gripping surface, except...
-
11B-609.4 Position of grab bars
Grab bars shall be installed in a horizontal position, 33 inches (838 mm) minimum and 36 inches (914 mm) maximum above the finish floor measured to the top of the gripping surface, except...
-
Architect
Recommend working with a hardware consultant or manufacturer's technical rep for exact specifications on the top jamb mounted configuration....