Swiveling gooseneck spout with 7-3/8" clearance. Replaceable seats. Brass quarter turn quick compression stem units. Replaceable reinforced nitrile rubber packing....
Search Results "Vertical Clearance"
Filters
Commonly Searched Documents
-
Just Manufacturing Ledgemount Swivel Gooseneck Mixing Faucet
-
Table Surface Height
Some commenters also recommended a higher minimum height of 29 inches instead of 28 inches to allow a more comfortable knee clearance. Response....
-
Accessible Route Into and Through the Business
Customers with disabilities will not be able to shop in a store if the route through an entry plaza is too narrow because of a display of snow blowers, if the maneuvering clearance alongside...
-
703.2.5 Character Height
Character height measured vertically from the baseline of the character shall be 5/8 inch (16 mm) minimum and 2 inches (51 mm) maximum based on the height of the uppercase letter "I"....
-
504.5 Nosings
Risers shall be permitted to slope under the tread at an angle of 30 degrees maximum from vertical....
-
703.2.5 Character Height
Character height measured vertically from the baseline of the character shall be 5/8 inch (16 mm) minimum and 2 inches (51 mm) maximum based on the height of the uppercase letter "I"....
-
504.5 Nosings
Risers shall be permitted to slope under the tread at an angle of 30 degrees maximum from vertical....
-
1008.3.2.3 Transfer Supports
Some examples of supports include a rope loop, a loop type handle, a slot in the edge of a flat horizontal or vertical member, poles or bars, or D rings on the corner posts....
-
7.4.5.1 Size
Vertical alignment at the intersection of the trails that form the T-shaped space shall be nominally level....
-
Spout Location [4.15.3]
The trajectory of water flow must be vertically "parallel" or "nearly parallel" to the face of the unit....
-
§ 38.73(d)(1) Requirements
Vertical alignment may be accomplished by vehicle air suspension, automatic ramps or lifts, or any combination....
-
11B-703.2.5 Character height
Character height measured vertically from the baseline of the character shall be 5/8 inch (15.9 mm) minimum and 2 inches (51 mm) maximum based on the height of the uppercase letter “I”....
-
Surfaces (R302.7) (Section-by-Section Analysis)
Vertical alignment of surfaces within pedestrian access routes (including curb ramp runs, blended transitions, turning spaces, and gutter areas within pedestrian access routes) and within...
-
Corbin Russwin Inc. ED7000 Series Narrow Stile Crossbar Exit Device
The ED7000 Series are available as Rim, Surface Vertical Rod, Mortise and Concealed Vertical Rod devices. ...
-
PDQ 4200 Series Exit Device Door Hardware
The American Eagle 4200 Series is a rim or surface vertical rod exit device....
-
Husky 24" Line Generator Digital Laser Level
This level may use indoors or out for horizontal (level), vertical (plumb) and square alignment projects....
-
Pilot Rock WXT and WXTH Picnic Table Using Lumber
The WXT Series offers clearances under the table top of 30” wide, 27” high, and 24” total knee and toe clearance (19” knee and 5” toe). Nominal seat height is 18”....
-
Pilot Rock WUT and WUTH Picnic Table Using Recycled Plastic
The WUT Series offers clearances under the table top of 30” wide, 27” high, and 24” total knee and toe clearance (19” knee and 5” toe). Nominal seat height is 18”....
-
Pilot Rock WUT and WUTH Picnic Table Using Formed Steel Channel
The WUT Series offers clearances under the table top of 30” wide, 27” high, and 24” total knee and toe clearance (19” knee and 5” toe). Nominal seat height is 18”....
-
Pilot Rock WXT and WXTH Picnic Table Using Recycled Plastic
The WXT Series offers clearances under the table top of 30” wide, 27” high, and 24” total knee and toe clearance (19” knee and 5” toe). Nominal seat height is 18”....
-
Pilot Rock WXT and WXTH Picnic Table Using Expanded Steel
The WXT Series offers clearances under the table top of 30” wide, 27” high, and 24” total knee and toe clearance (19” knee and 5” toe). Nominal seat height is 18”....
-
Pilot Rock WUT and WUTH Picnic Table Using Lumber
The WUT Series offers clearances under the table top of 30” wide, 27” high, and 24” total knee and toe clearance (19” knee and 5” toe). Nominal seat height is 18”....
-
11B-410.7 Landing size
ETA Editor's Note There are no requirements for landing size in 2010 ADA Standards, although the door maneuvering clearance requirements at 404.2.4 should be applicable outside the platform...
-
Inclusion Solutions Offset Door Hinge
These special hinges are designed to swing the door clear of the opening, adding about 2" additional clearance for wheelchairs and walkers....
