The visible signal elements shall be 2½ inches (64 mm) minimum measured along the vertical centerline of the element....
Search Results "Vertical Clearance"
Filters
Commonly Searched Documents
-
407.2.2.2 Visible Signals
-
Gaps
spaces are provided on amusement rides, the floors of rides must be coordinated with the floors of the load and unload areas so that when the ride is at the load and unload position, the vertical...
-
608.7 Thresholds
In transfer type shower compartments, thresholds 1/2 inch (13 mm) high maximum shall be beveled, rounded, or vertical....
-
407.2.2.2 Visible Signals
The visible signal elements shall be 2 1/2 inches (64 mm) minimum measured along the vertical centerline of the element....
-
Adjustable height protocol
The amount of vertical distance that the seat was raised/lowered each time depended on the subject’s perceived and observed transfer abilities....
-
Engineered vs. Outside
The seat values are of particular importance because vertical vibrations transferred through the seat of a seated individual are the most hazardous....
-
4.34.6.8* REFRIGERATOR/FREEZER
Provision shall be made for refrigerators which are: (1) Of the vertical side-by-side refrigerator/freezer type; or (2) Of the over-and-under type and meet the following requirements...
-
11B-303.3 Beveled
A change in level of ½ inch (13 mm) is permitted to be ¼ inch (6.4 mm) vertical plus ¼ inch (6.4 mm) beveled....
-
§ 38.159(b)(8) Platform entrance ramp
loading-edge barrier used as a ramp, shall not exceed a slope of 1:8, measured on level ground, for a maximum rise of 3 inches (75 mm), and the transition from roadway or sidewalk to ramp may be vertical...
-
Feature 2 - Routes to the Building Entrance
Ramps with a vertical rise of more than 6 inches must have handrails on both sides....
-
Don-Jo Mfg., Inc. Pull Plate 7011
Number 7011 Dimensions 3-1/2" x 15" Ansi J405 Ctc 5-1/2" Diameter 5/8" Projection 2" Clearance...
-
Bobrick MatrixSeries Seat-Cover Dispenser B-5221
Allow 5" (125mm) minimum clearance from bottom of dispenser to top of any horizontal projection for filling dispenser from below unit....
-
4.3.9 Doorway Design
The lack of differences between the findings for the passage task on the pull sides of Doors 1, 800 mm (31.5 in.) latch clearance, and Door 2, 406 mm (16 in.) latch clearance, demonstrate...
-
a. Structural Strength
The MDE NPRM proposed to require transfer supports to be capable of resisting vertical and horizontal forces of 250 pounds at all points (proposed M305.2.2)....
-
304 Turning Space
Objects that provide sufficient knee and toe clearance can overlap a limited portion of the turning space. Comment....
-
Section 810.2.2
We note that there may be some instances in which it will be necessary to make operational adjustments where sufficient clearance is not available to permit the deployment of lifts or ramps...
-
4.10.9 Floor Plan of Elevator Cars
The clearance between the car platform sill and the edge of any hoistway landing shall be no greater than 1‒1/4 in (32 mm)....
-
4.10.9 FLOOR PLAN OF ELEVATOR CARS
The clearance between the car platform sill and the edge of any hoistway landing shall be no greater than 1-1/4 in (32 mm)....
-
Clear Floor or Ground Space and Turning Space
Clearances are required at accessible elements, fixtures, and controls so that people with disabilities, including those who use wheelchairs, can approach and use them....
-
Pilot Rock WXT and WXTH Picnic Table Using Aluminum
The WXT Series offers clearances under the table top of 30” wide, 27” high, and 24” total knee and toe clearance (19” knee and 5” toe). Nominal seat height is 18”....
-
Pilot Rock WUT and WUTH Picnic Table - Using Aluminum
The WUT Series offers clearances under the table top of 30” wide, 27” high, and 24” total knee and toe clearance (19” knee and 5” toe). Nominal seat height is 18”....
-
Bobrick ConturaSeries Surface-Mounted Seat-Cover Dispenser B-4221
Allow 5" (125mm) minimum clearance from bottom of dispenser to top of any horizontal projection for filling dispenser from below unit....
-
Bobrick Recessed Paper Towel Dispenser B-318
Rough Wall Opening: 12" W, 18 1⁄4" H (305 x 465mm) to accept cabinet height, plus 6" (150mm) min. clearance space below towel tray; 4 1⁄2" (115mm) min. depth....
-
Transfer Protocols
The maximum and minimum vertical distances that were attainable were recorded....
