MEASUREMENT TECHNIQUE The depth and width are measured along the centerlines of the seat, and the height from the floor to the highest point of the transfer surface: The depth...
Search Results "Sink Height"
-
MEASUREMENT TECHNIQUE
-
1132A.4, Item 3
., concrete, brick, flagstone) may have a maximum change in height from the interior landing of 4 inches (101.6 mm)....
-
§ 38.53(d)(1) Requirements
vehicles shall be coordinated with the boarding platform design such that the horizontal gap between each vehicle door at rest and the platform shall be no greater than 3 inches and the height...
-
1009.5.4 Transfer Steps
Transfer step height shall be 8 inches (205 mm) maximum....
-
Addition
An expansion, extension, or increase in the gross floor area or height of a building or facility....
-
106.5.3 Addition
An expansion, extension, or increase in the gross floor area or height of a building or facility....
-
3) Signs
rooms and spaces (men's and women's rooms; room numbers; exit signs) must have raised and Brailled letters; must comply with finish and contrast standards; and must be mounted at a certain height...
-
Accessibility to Perform the Essential Functions of the Job
parking spaces close to the work site that are wide enough to allow people using wheelchairs to get in and out of vehicles; making restrooms accessible, including toilet stalls, sinks...
-
809.2.2 Turning Space
It would, therefore, be unacceptable to use both the clearances under the work surface and the sink as part of a T-turn. See 304.3.2 regarding T-turns....
-
809.2.2 Turning Space
It would, therefore, be unacceptable to use both the clearances under the work surface and the sink as part of a T-turn. See Section 304.3.2 regarding T-turns....
-
809.2.2 Turning Space
It would, therefore, be unacceptable to use both the clearances under the work surface and the sink as part of a T-turn. See 304.3.2 regarding T-turns....
-
11B-603.5 Accessories
ETA Editor's Note The CBC 11B-603.5 limitation on the height of accessories at toilet rooms is more stringent than 2010 ADA Standards....
-
11B-803.1 General
Section 11B-903.5 requires dressing room bench seats to be installed so that they are at the same height as a typical wheelchair seat, 17 inches (430 mm) to 19 inches (485 mm)....
-
11B-603.5 Accessories
ETA Editor's Note The CBC 11B-603.5 limitation on the height of accessories at toilet rooms is more stringent than 2010 ADA Standards....
-
11B-803.1 General
Section 11B-903.5 requires dressing room bench seats to be installed so that they are at the same height as a typical wheelchair seat, 17 inches (430 mm) to 19 inches (485 mm)....
-
Addition
An expansion, extension, or increase in the gross floor area or height of a building or facility....
-
Thresholds at Doorways [4.13.8]
ADAAG specifies a maximum threshold height of ½ inch, but allows a height up to ¾ inch at exterior sliding doors where necessary to prevent water damage....
-
[A] 101.2 Scope
Exception: Detached one- and two-family dwellings and multiple single-family dwellings (townhouses) not more than three stories above grade plane in height with a separate means of egress...
-
101.2 Scope
Exception: Detached one- and two-family dwellings and townhouses not more than three stories above grade plane in height with a separate means of egress, and their accessory structures...
-
SafePath: Threshold Ramp Installation for MultiFamily Housing for Disability Access
One of the largest violations of Fair Housing Act (FHA) regulations is the treatment or perceived compliance specific to threshold heights. ...
-
11B-703.2.6 Stroke thickness
Stroke thickness of the uppercase letter “I” shall be 15 percent maximum of the height of the character....
-
1132A.4.1, Item 1
Thresholds with a change in height of not more than ¼ inch (6.35 mm) may be vertical....
-
703.2.6 Stroke Thickness
Stroke thickness of the uppercase letter “I” shall be 15 percent maximum of the height of the character....
-
Station platforms
Station platforms must be coordinated with the vehicle floor height. (DOT ADA Standard 810.5.3.)...
