Data from the maximum and minimum height transfers from protocol A were used for this analysis....
Search Results "Sink Height"
-
Sample Size Estimation
-
[A] ADDITION
[DSA-AC] An expansion, extension, or increase in the gross floor area or height of a building or facility....
-
SUMMARY OF THE 19-INCH RECOMMENDATION
Access Board’s Medical Diagnostic Equipment Technical Advisory Committee discussed transfer surface height extensively....
-
Notes
Seat heights for males were typically higher than for females....
-
Podium
Podium: If a podium is used, some speakers who use mobility devices may not be able to use one that is standard height....
-
Side Reach [4.2.6]
Since the height of reach decreases with depth, the maximum high reach is limited to 46 inches over obstructions no more than 24 inches deep and 34 inches high....
-
1012.3 Opening limitations
Open guards shall have balusters or ornamental patterns such that a 4-inch-diameter (102 mm) sphere cannot pass through any opening up to a height of 34 inches (864 mm)....
-
IMPLICATION OF A 19-INCH MINIMUM STANDARD FOR THE HIGHEST POINT IN THE LOWEST ADJUSTABLE POSITION
However, shorthand references to 19 inches as the minimum standard as used in this minority report should not be equated with a 19-inch transfer surface height, for two major reasons....
-
11B-604.5 Grab bars
Where separate grab bars are required on adjacent walls at a common mounting height, an L-shaped grab bar meeting the dimensional requirements of Sections 11B-604.5.1 and 11B-604.5.2 shall...
-
11B-604.5 Grab bars
Where separate grab bars are required on adjacent walls at a common mounting height, an L-shaped grab bar meeting the dimensional requirements of Sections 11B-604.5.1 and 11B-604.5.2 shall...
-
703.5.7 Stroke Thickness
Stroke thickness of the uppercase letter "I" shall be 10 percent minimum and 30 percent maximum of the height of the character....
-
605 Urinals
Section 604.5 provides criteria for accessible urinals, including the height and depth, clear floor space, and flush controls....
-
703.5.7 Stroke Thickness
Stroke thickness of the uppercase letter “I” shall be 10 percent minimum and 30 percent maximum of the height of the character....
-
703.2.6 Stroke Thickness
Stroke thickness of the uppercase letter "I" shall be 15 percent maximum of the height of the character. [ECTCR UFAS 4.30.4]...
-
T702.5 Stroke Thickness
Stroke thickness of the uppercase letter “I” shall be 10 percent minimum and 30 percent maximum of the height of the character....
-
703.5.7 Stroke Thickness
Stroke thickness of the uppercase letter "I" shall be 10 percent minimum and 30 percent maximum of the height of the character....
-
703.2.6 Stroke Thickness
Stroke thickness of the uppercase letter "I" shall be 15 percent maximum of the height of the character....
-
Attachment H: Modifications to Altered Facilities
Attachment H: Modifications to Altered Facilities
-
ADDENDUM TO PHASE I FINAL REPORT: Points of Clarification
The Adjustable Height protocol included two types of transfers, a transfer to a higher height and a transfer to a lower height relative to the mobility device's seat to floor height....
-
11B-809.2.2 Turning space
It would, therefore, be unacceptable to use both the clearances under the work surface and the sink as part of a T-turn. See 304.3.2 regarding T-turns....
-
Kitchen Counters, Walls, and Floors
Counters all on one level for sliding heavy pans Fruit bowl/sink on the counter to encourage healthy eating (plumbed for washing fruit)....
-
Operating Hardware
Result: Persons who have the use of only one hand or who have limited use of hands, wrists, or arms are unable to open doors to get into rooms, lock doors for security, use sinks or showers...
-
11B-809.2.2 Turning space
It would, therefore, be unacceptable to use both the clearances under the work surface and the sink as part of a T-turn. See 304.3.2 regarding T-turns....
-
11B-809.2.2 Turning space
It would, therefore, be unacceptable to use both the clearances under the work surface and the sink as part of a T-turn. See Section 11B-304.3.2 regarding T-turns. ◼...