Installation guide for the DH2 Door Handle, including Single-Sided and Back to Back Mounting installations. ...
Search Results "Latch Side Clearance"
Filters
Commonly Searched Documents
-
Mockett DH2 Door Handle Installation
-
11B-405.9 Edge protection
Edge protection complying with Section 11B-405.9.2 shall be provided on each side of ramp runs and at each side of ramp landings. [2010 ADA Standards] 405.9 Edge Protection....
-
11B-813.2.10 Door swing
Where a clear floor space complying with Section 11B-305.3 is provided within the room beyond the arc of the door swing, doors shall be permitted to swing into the clear floor space, clearance...
-
Delta 1-1/2″ x 36″ ADA Grab Bar Concealed Mounting 40136-PS
Product Features and Benefits 36″ long, 1 1/2″ wide Concealed mounting - mounting hardware included 3″ diameter flanges 1 1/2″ wall clearance Limited Faucet and Finish Warranty...
-
Boolee Voting Booth
Materials: 1” Aluminum Frame Table is ABS sheet All fasteners are zinc plated All side panel fabric is 300 x 300 urethane-coated polyester Design Specifications All weights and...
-
Delta 1-1/2″ x 18″ ADA Grab Bar, Concealed Mounting 40118-PS
Product Features and Benefits 18″ long, 1 1/2″ wide Concealed mounting - mounting hardware included 3″ diameter flanges 1 1/2″ wall clearance Limited Faucet and Finish Warranty...
-
9.5 LOCKER ROOMS
Lockers intended for use by handicapped people shall be equipped with latches and latch handles that comply with 4.27....
-
Corbin Russwin Inc. DC5000 Series Cam Action Door Closer
The DC5000 series cam action door closers come standard with adjustable sweep speed and latch speed, closing control and adjustable back check cushioning in the opening cycle....
-
1011.2.1 Size and Location
space Viewing Scopes 36 inches (915 mm) by 48 inches (1220 mm) positioned for forward approach to the viewing scope Provide knee and toe clearance...
-
1011.2.1 Size and Location
space Viewing Scopes 36 inches (915 mm) by 48 inches (1220 mm) positioned for forward approach to the viewing scope Provide knee and toe clearance...
-
A4.2.1(1) Space Requirements for Wheelchairs
For most situations, the addition of an inch of leeway on either side is sufficient. Thus, a minimum clear width of 32 in (815 mm) will provide adequate clearance....
-
A4.2.1(1) Space Requirements for Wheelchairs
For most situations, the addition of an inch of leeway on either side is sufficient. Thus, a minimum clear width of 32 in (815 mm) will provide adequate clearance....
-
Clear Floor Space [4.16.2]
amount of space required at an accessible toilet, not the minimum room size, which must also include turning space, clear floor space at other provided fixtures, door swing and maneuvering clearance...
-
Figure 608.2.1 Transfer Type Shower Compartment Size and Clearance – Drawing from the U.S. Access Board
-
Allegion Falcon 2390 Series Recessed Exit Device
Specifications Hand: Field reversible, non handed Functions: See trim selection chart Finishes: US28, DC13, DC35, Champagne Strikes: PB48 top Latches...
-
Edge Protection: ADA Standard Section 405.9
Section 405.9 covers the current ADA Standards for edge protection at ramps.
-
Where Required: ADA Standard Section 505.2
Section 505.2 covers the current ADA Standards for where handrails are required.
-
Allegion LCN 4000 Series Surface Mounted Door Control
Features and Benefits Each closer (except 4040, 4040T, 4030, 4030T) is designed for a specific mounting; hinge side, top jamb, or parallel arm. 4040 closer with regular or hold-open...
-
Pass Through Kitchen
Clearances for pass through kitchens address counters, appliances, or cabinets on two opposing sides....
-
Pilot Rock WPTS Square Frame Table Using Recycled Plastic
Full length seats offer full capacity seating which is an advantage over extended top or side access tables....
-
Pilot Rock WPTS Square Frame Table Using Lumber
Full length seats offer full capacity seating which is an advantage over extended top or side access tables....
-
CRL Jackson 900 Series Floor Mounted Door Closers
The Door Closer has separate valves to control closing and latching speeds. 90 Degree Hold Open and No Hold Open models are available....
-
Door and Gate Opening Force: ADA Standard Section 404.2.9
Section 404.2.9 covers the current ADA Standards for door and gate opening force.
-
4.13.11(2)(c)
(c) sliding or folding doors: 5 lbf (22.2N) These forces do not apply to the force required to retract latch bolts or disengage other devices that may hold the door in a closed position...
