Clearance around a water closet shall be 60 inches (1525 mm) minimum measured perpendicular from the side wall and 56 inches (1420 mm) minimum measured perpendicular from the rear wall....
Search Results "Latch Side Clearance"
Filters
Commonly Searched Documents
-
604.3.1 Size
-
Operable Parts: ADA Standard Section 804.6.2
Appliance doors and door latching devices shall not be required to comply with 309.4. 2....
-
Access Board: Sales and Service Counters
Demonstration of sales and service counters that are accessible to people with disabilities according to accessibility standards issued under the American with Disabilities Act (ADA)...
-
Rockwood Manufacturing Company 596 Hospital Push Pull Latch 5" Backset
Material: Stainless Steel FEATURES: • Easy to operate low-force paddle. • Non-handed (except for engraved models). • Includes Standard 161 and ASA strike. • 2-3/4", 5" or 7"...
-
ELKAY Filtered EZH2O® Bottle Filling Station with Integral Soft Sides® Fountain LZWS-EDFP217K
The Elkay EZH2O Bottle Filling Station delivers a clean quick water bottle fill and enhances sustainability by minimizing our dependency on disposable plastic bottles. Complete...
-
Transfer Entry
Transfer Entry There is a large amount of variance in amusement rides and the sides of the ride are often part of the restraint or securement system....
-
Door Hardware [4.13.9]
Door Hardware [4.13.9] Hardware used to operate doors, including handles, pulls, latches and locks, must have a shape that is "easy to grasp with one hand" and does not require tight...
-
11B-804.6.2 Operable parts
Exceptions: Appliance doors and door latching devices shall not be required to comply with Section 11B-309.4....
-
608.2.3 Alternate Roll-In Type Shower Compartments
Alternate roll-in type shower compartments shall be 36 inches (915 mm) wide and 60 inches (1525 mm) deep minimum clear inside dimensions measured at center points of opposing sides....
-
608.2.2 Standard Roll-In Type Shower Compartments
Standard roll-in type shower compartments shall be 30 inches (760 mm) wide minimum by 60 inches (1525 mm) deep minimum clear inside dimensions measured at center points of opposing sides...
-
4.13.9* DOOR HARDWARE
Handles, pulls, latches, locks, and other operating devices on accessible doors shall have a shape that is easy to grasp with one hand and does not require tight grasping, tight pinching...
-
608.2.1 Transfer Type Shower Compartments
Transfer type shower compartments shall be 36 inches (915 mm) by 36 inches (915 mm) clear inside dimensions measured at the center points of opposing sides and shall have a 36 inch (915...
-
11B-404.3 Automatic and power-assisted doors and gates
An automatic door may be used as equivalent facilitation when it is technically infeasible to provide sufficient strike-side clearance for code compliance, but a power-assisted door may...
-
General [9.1.1]
Where room numbers are provided, they must be raised and Brailled and located on the wall at the latch-sides of doors for safety and uniformity....
-
Caution regarding minimum Aisle Widths for aisles that serve "elements on both sides"
The interpretation of the meaning of aisles "serving elements on both sides" might be taken by some AHJs to mean public access to aisles that have self-serve items on both sides of an aisle...
-
Lavatory & Accessory Layouts
The trash receptacle is preferred to be near the door to allow people to pull the door open with a paper towel and drop it into the receptacle before exiting.
-
1118B.6
SECTION 1118B - SPACE ALLOWANCE AND REACH RANGES 1118B.6 Side reach. ...
-
C) Accessible Entrance
If a door is provided, there must be maneuvering space on the pull and push sides of the door to permit a person using a wheelchair to open the door and then move through the door opening...
-
Temporary Solutions for Election Day: Accessible Entrance to Polling Place
Problem Three: Entrance door threshold has an abrupt change in level of more than 1/4 inch and no beveled sides....
-
Are doors or gates to employee work areas required to comply?
Entry doors or gates to employee work areas are required to meet applicable requirements, including those for maneuvering clearance, on the exterior, but not the interior....
