5.4 Transfer Supports Recommendations
Search Results "Surface Discontinuities"
Commonly Searched Documents
-
5.4 Transfer Supports Recommendations
-
M305.2 Transfer Supports
Transfer supports shall comply with M305.2.
- Boost Your Business - Chapter 4 - Ramps
-
C201.4 Prohibited Reduction of Accessibility, Usability, and Compatibility
EXCEPTION: Discontinuation of a product shall not be prohibited....
-
1.2.4
1.2.4 When local horizontal discontinuities and vertical alignments are measured according to Section 1.1.9 a recommended tolerance is ±1/8 in. (3 mm)....
-
Detectable Warning Surfaces on Curb Ramps (Section-by-Section Analysis)
Detectable Warning Surfaces on Curb Ramps (Section-by-Section Analysis) When the Access Board issued the 1991 ADAAG, the guidelines contained a requirement for detectable warning surfaces...
-
5.3.1 Permitted Obstructions to Transfer Sides for Equipment Used by Patients in a Supine, Prone, Side-Lying or Seated Position
5.3.1 Permitted Obstructions to Transfer Sides for Equipment Used by Patients in a Supine, Prone, Side-Lying or Seated Position. A 3-inch maximum obstruction is permitted at transfer...
-
R105 Definitions (Section-by-Section Analysis)
ramp, element, facility, grade break, operable part, pedestrian access route, pedestrian circulation path, public right-of-way, qualified historic facility, running slope, and vertical surface...
-
11B-809.9.7 Exposed pipes and surfaces
Exposed water supply and drain pipes under sinks and lavatories shall comply with Section 11B-606.5.
-
Appendix C: Previous Research on the Visibility of Detectable Warning Surfaces
1.1 m (42 in.) x 1.1 m (42 in.) detectable warning surfaces....
-
5.4.3.1 Positioning Support Height Recommendation for Imaging Equipment with Transfer Surfaces
5.4.3.1 Positioning Support Height Recommendation for Imaging Equipment with Transfer Surfaces For imaging equipment with transfer surfaces, the Committee recommends a positioning support...
-
26. Please indicate who installed the trail surface
Please indicate who installed the trail surface (choose all that apply): Manufacturer Contractor Agency/Organization/Park staff Volunteer Unknown...
-
C201.4 Prohibited Reduction of Accessibility, Usability, and Compatibility
EXCEPTION: Discontinuation of a product shall not be prohibited....
-
Methodology
This study was approved by the University of Pittsburgh's Institutional Review Board and all participants provided informed consent before participating in any test procedures.
-
Openings in Outdoor Recreation Access Route Surfaces
Openings are gaps in the surface of an outdoor recreation access route. Gaps include spaces between the planks on a boardwalk or in a drainage grate....
- Boost Your Business - Chapter 6 - Doors
-
Play Areas
Word Fillable Form (0.4MB) Word Non-Fillable Form (0.3MB) PDF Non-Fillable Form (0.3MB)
-
25. Please indicate the date (year) of trail surface installation
Please indicate the date (year) of trail surface installation:...
-
What values are recommended for ground and floor surfaces along an accessible route?
What values are recommended for ground and floor surfaces along an accessible route?...
-
Durability and Maintenance of Detectable Warning Surfaces (Section-by-Section Analysis)
Durability and Maintenance of Detectable Warning Surfaces (Section-by-Section Analysis) Transportation officials who commented on the 2002 draft guidelines expressed concern about the...
-
Why a smooth surface door or kickplate is important
Remember that the latch that hits the push rim is nicking the surface your fingers have to grasp thousands of times a day for years....
-
Investigation
LCG: (i) refused to provide assistance with insulin administration (by pen or syringe) to children with Type I diabetes based on a corporate-wide policy requiring such refusal and (ii) discontinued...
-
What other considerations are significant for persons with disabilities?
Thus, walks surfaced in these materials could not constitute an accessible route....