R302.7.2 Vertical Surface Discontinuities. Vertical surface discontinuities shall be 13 mm (0.5 in) maximum....
Search Results "Surface Discontinuities"
Filters
Commonly Searched Documents
-
R302.7.2 Vertical Surface Discontinuities
-
Surface discontinuities
Differences in level between two adjacent surfaces. Elevation changes due to ramps or stairs do not, themselves, constitute surface discontinuities....
-
T302.4 Surface Discontinuities
Surface discontinuities shall be ½ inch (13 mm) high maximum and shall be beveled with a slope not steeper than 1:2. EXCEPTIONS: 1....
-
Vertical Surface Discontinuities
Vertical Surface Discontinuities. Vertical differences in level between two adjacent surfaces....
-
T302 Walking Surfaces
[See subsections ...]
-
T302.1 General
Walking surfaces in non-rail vehicles shall comply with T302. EXCEPTION: Walking surfaces on lifts shall not be required to comply with T302....
-
Gripping Surface: ADA Standard Section 505.6
Section 505.6 covers the current ADA Standards for the handrail gripping surface.
-
T302 Walking Surfaces
The technical requirements for walking surfaces include provisions on slip resistance, the maximum size of surface openings, and the maximum height of vertical surface discontinuities (i.e...
-
Surface: ADA Standard Section 810.2.1
Bus stop boarding and alighting areas shall have a firm, stable surface....
-
Floor or Ground Surface: ADA Standard Section 403.2
Section 403.2 covers the current ADA Standards for floor or ground surfaces that are part of an accessible route.
-
T402.9 Transitions
Vertical surface discontinuities at transitions from boarding and alighting areas to ramps and bridgeplates shall comply with T302.4....
-
Floor or Ground Surface: ADA Standard Section 1002.4.1
The floor or ground surface of wheelchair spaces shall be stable and firm....
-
Floor or Ground Surface: ADA Standard Section 802.1.1
The floor or ground surface of wheelchair spaces shall comply with 302. Changes in level are not permitted. EXCEPTION: Slopes not steeper than 1:48 shall be permitted....
-
Tread Surface: ADA Standard Section 504.4
Section 504.4 covers the current ADA Standards for the tread surfaces on stairways.
-
Floor or Ground Surface: ADA Standard Section 404.2.4.4
Section 404.2.4.4 covers the current ADA Standards for floor or ground surfaces at door maneuvering clearances.
-
Extended Floor or Ground Surface: ADA Standard Section 405.9.1
Section 405.9.1 covers the current ADA Standards for extended floor or ground surface of the ramp run or landing.
-
Surface Hazards: ADA Standard Section 609.5
Section 609.5 covers the current ADA Standards for the surfaces of grab bars and adjacent surfaces.
-
Openings: ADA Standard Section 302.3
Section 302.3 covers the current ADA Standards for floor and ground surface openings.
-
Exposed Surfaces: ADA Standard Section 804.3.3
There shall be no sharp or abrasive surfaces under the work surface counters....
-
11B-403.2 Floor or ground surface
Floor or ground surfaces shall comply with Section 11B-302....
-
11B-804.3.3 Exposed surfaces
There shall be no sharp or abrasive surfaces under the work surface counters....
-
Door and Gate Surfaces: ADA Standard Section 404.2.10
Section 404.2.10 covers the current ADA Standards for door and gate surfaces on manual doors and gates.
-
Kitchen Work Surface: ADA Standard Section 804.3
In residential dwelling units required to comply with 809, at least one 30 inches (760 mm) wide minimum section of counter shall provide a kitchen work surface that complies with 804.3....
-
11B-404.2.10 Door and gate surfaces
Swinging door and gate surfaces within 10 inches (254 mm) of the finish floor or ground measured vertically shall have a smooth surface on the push side extending the full width of the door...