Semi-Recessed - 1 1/4", 1 1/2" Square Edge, 2-1/2" Formed Rolled Edge, 3", 4" and 4-1/2" Rolled Edge constructed of aluminum extrusion (4" has ADA pull)....
Search Results "Platform Edge"
Filters
Commonly Searched Documents
-
Activar JL Industries Academy Series 1027V10 Aluminum Fire Extinguisher Cabinet
-
Chapter 5: Software (Section-by-Section Analysis)
Chapter 5 contains proposed technical requirements for software, applications, platforms, and software tools....
-
4.3.8 CHANGES IN LEVELS
If an accessible route has changes in level greater than 1/2 in (13 mm), then a curb ramp, ramp, elevator, or platform lift shall be provided that complies with 4.7, 4.8, 4.10, or 4.11,...
-
Roundabouts (Section-by-Section Analysis)
Where sidewalks are flush against the curb at roundabouts and pedestrian street crossing is not intended, a continuous and detectable edge treatment must be provided along the street side...
-
11B-302.2 Carpet
Exposed edges of carpet shall be fastened to floor surfaces and shall have trim on the entire length of the exposed edge....
-
11B-302.2 Carpet
Exposed edges of carpet shall be fastened to floor surfaces and shall have trim on the entire length of the exposed edge....
-
11B-302.2 Carpet
Exposed edges of carpet shall be fastened to floor surfaces and shall have trim on the entire length of the exposed edge. Carpet edge trim shall comply with Section 11B-303....
-
QUESTION: WHERE THE TRACK ADJACENT TO A PLATFORM IS NOT SHARED WITH FREIGHT, ARE THERE ANY CIRCUMSTANCES IN WHICH AN APPROACH OTHER THAN LEVEL BOARDING IS ALLOWABLE?
ANSWER: There may be some situations where level boarding is not physically feasible (e.g., where the curvature of the track is too great to make level boarding...
-
Ramps
They must meet the ADA's requirements regarding slope, width, landings, handrails, and edge protection....
-
11B-404.2.10 Door and gate surfaces
Parts creating horizontal or vertical joints in these surfaces shall be within 1/16 inch (1.6 mm) of the same plane as the other and be free of sharp or abrasive edges....
-
4. Wheelchair seat depth
., towards the rear) edge to the distal (i.e., towards the forward) edge of the wheelchair seat cushion....
-
1.1.17 Stairs
For stairs 60 in. (1520 mm) or less in width, measure along a line approximately 18 in. (460 mm) from the wall or outside edge of the stair....
-
11B-404.2.10 Door and gate surfaces
Parts creating horizontal or vertical joints in these surfaces shall be within 1/16 inch (1.6 mm) of the same plane as the other and be free of sharp or abrasive edges....
-
11B-404.2.10 Door and gate surfaces
Parts creating horizontal or vertical joints in these surfaces shall be within 1/16 inch (1.6 mm) of the same plane as the other and be free of sharp or abrasive edges....
-
SATECH, Inc. SmartCells Classic Ant-Fatigue Mat
The Classic SmartCells® Anti-Fatigue mat features a smooth surface, molded in rubber edges and an 8 year warranty....
-
9 [§ 4.7.5]
9 [§ 4.7.5] Curb ramps either have flared sides or vertical edges called returned curbs....
-
11B-1009.2.3 Clear deck space
The space shall be 36 inches (914 mm) wide minimum and shall extend forward 48 inches (1219 mm) minimum from a line located 12 inches (305 mm) behind the rear edge of the seat....
-
307.4 Vertical Clearance
The leading edge of such guardrail or barrier shall be located 27 inches (685 mm) maximum above the finish floor or ground....
-
610.2 Bathtub Seats
Permanent seats at the head end of the bathtub shall be 15 inches (380 mm) deep minimum and shall extend from the back wall to or beyond the outer edge of the bathtub....
-
Gripping Surface Cross Section and Clearances M301, M302, and M305.2
Gripping Surface Cross Section and Clearances M301, M302, and M305.2 Gripping surface for transfer supports shall be free of sharp or abrasive elements and shall have rounded edges per...
-
R305.2.5 Pedestrian At-Grade Rail Crossings
The edge of the detectable warning surface nearest the rail crossing shall be 1.8 m (6.0 ft) minimum and 4.6 m (15.0 ft) maximum from the centerline of the nearest rail....
-
602.2 Clear Floor Space
complying with 305 shall be permitted at units for children’s use where the spout is 30 inches (760 mm) maximum above the finish floor or ground and is 3½ inches (90 mm) maximum from the front edge...
-
M9
Does the lavatory have at least a 29-inch-high clearance under the front edge and the top of the rim no more than 34 inches above the floor?...
-
1009.2.3 Clear Deck Space
The space shall be 36 inches (915 mm) wide minimum and shall extend forward 48 inches (1220 mm) minimum from a line located 12 inches (305 mm) behind the rear edge of the seat....
