M301.4.2 and M302.4.2 would require the base of the equipment to provide a clearance 6 inches high minimum measured from the floor and 36 inches deep minimum measured from the edge of the...
Search Results "Platform Edge"
Filters
Commonly Searched Documents
-
Clearance Around Base (M301.4.2 and M302.4.2)
-
Ramp
A ramped surface was made to attach between the two transfer platforms ('steps') and span across an 8 inch wide space. ...
-
11B-803.6 Mirrors
Mirrors shall be installed with the bottom edge of the reflecting surface 20 inches (508 mm) maximum above the finish floor or ground....
-
404.2.5 Thresholds
EXCEPTION: Existing or altered thresholds 3/4 inch (19 mm) high maximum that have a beveled edge on each side with a slope not steeper than 1:2 shall not be required to comply with 404.2.5...
-
404.2.5 Thresholds
EXCEPTION: Existing or altered thresholds 3/4 inch (19 mm) high maximum that have a beveled edge on each side with a slope not steeper than 1:2 shall not be required to comply with 404.2.5...
-
407.8.2 Side Reach
The vertical reference plane shall be centered on the operable part and placed at the leading edge of the maximum protrusion of the ICT within the length of the vertical reference plane....
-
504.4 Tread Surface
Consider providing visual contrast on tread nosings, or at the leading edges of treads without nosings, so that stair treads are more visible for people with low vision....
-
Problem Four
Cones mark the access aisle and a temporary curb ramp with edge protection connects to an accessible route to the polling place....
-
Standard Units
Recessing units in alcoves, wing walls, or other means of providing a detectable leading edge at or below 27 inches are acceptable....
-
407.12.2 Side Reach
The vertical reference plane shall be centered on the operable part and placed at the leading edge of the maximum protrusion of the ICT within the length of the vertical reference plane....
-
4.34.3(2)(a) Reach Depth Not More Than 10 in
Where the reach depth to the operable parts of all controls as measured from the vertical plane perpendicular to the edge of the unobstructed clear floor space at the farthest protrusion...
-
A4.13.9 DOOR HARDWARE
To be effective, they should cover the door width, less approximately 2 in (51 mm), up to a height of 16 in (405 mm) form its bottom edge and be centered across the top....
-
11B-602.3 Operable parts
The flow of water shall be activated by a manually operated system that is front mounted or side mounted and located within 6 inches (152 mm) of the front edge of the fountain or an automatic...
-
11B-803.6 Mirrors
Mirrors shall be installed with the bottom edge of the reflecting surface 20 inches (508 mm) maximum above the finish floor or ground....
-
11B-803.6 Mirrors
Mirrors shall be installed with the bottom edge of the reflecting surface 20 inches (508 mm) maximum above the finish floor or ground....
-
§ 38.63(a) Requirement
Suitable devices or systems shall be provided to prevent, deter or warn individuals from inadvertently stepping off the platform between cars....
-
Car Dimensions and Doors: ADA Standard Section 408.4.1
Section 408.4.1 covers the current ADA Standards for the car dimensions and doors of limited-use/limited-application elevators.
-
When Transfer Systems Are Used
When Transfer Systems Are Used A transfer system provides access to elevated play components within a composite system by connecting different levels with transfer platforms and steps...
-
R305 Detectable Warning Surfaces (Section-by-Section Analysis)
At boarding platforms for buses and rail vehicles, detectable warning surfaces must extend the full length of the public use areas of the platform....
-
§ 36.406(f)(2)
(2) Wheelchair and companion seating locations are not located on (or obstructed by) temporary platforms or other movable structures. ...
-
11B-106.5 Defined terms
OCCUPIABLE SPACE OPEN RISER OPERABLE PART PASSENGER ELEVATOR PATH OF TRAVEL PEDESTRIAN PEDESTRIAN WAY PERMANENT PERMIT PICTOGRAM PLACE OF PUBLIC ACCOMMODATION PLATFORM...
-
Mirror Height
The guidelines specify that accessible mirrors be mounted so that the bottom edge of the reflecting surface is no higher than 40 inches (603.3)....
-
7(2)(b)(iv)
The other (non-grab bar) side of the toilet fixture is a minimum of 1'3" from the finished surface of adjoining walls, vanities or from the edge of a lavatory. (See Figure 7(a).)...
-
404.2.5 Thresholds
EXCEPTION: Existing or altered thresholds 3/4 inch (19 mm) high maximum that have a beveled edge on each side with a slope not steeper than 1:2 shall not be required to comply with 404.2.5...