.) (§404.2.5) E12 On the pull side of each door, is there at least 18" of clearance provided to the side of the latch?...
Search Results "Grab Bar Clearance"
Commonly Searched Documents
-
Section E: Route from Entrance
-
FIGURE INDEX
at Water Closets Figure 604.3.2 (Exception) Overlap of Water Closet Clearance in Residential Dwelling Units Figure 604.5.1 Side Wall Grab Bar at Water Closets Figure...
-
Can access be provided after construction based on need?
dwelling units or accessed through an individual’s private office for his or her exclusive use are not required to be built with certain specifically enumerated access features, such as grab...
-
Section A: Parking
Width of space _____ Width of access aisle _____ A3 For van accessible spaces (particularly in a garage or parking structure), is there vertical clearance...
- Mobi-Mat® Recpath™ ADA Beach Access Mat
-
Manual Doors and Gates [§404.2]
Manual Doors and Gates [§404.2]
-
Back Support: ADA Standard Section 903.4
To assist in transferring to the bench, consider providing grab bars on a wall adjacent to the bench, but not on the seat back....
-
4.21.2 SIZE AND CLEARANCES
Figure 35 Shower Size and Clearances...
-
Figure M3: Overview of M302 Diagnostic Equipment for Use by a Patient in a Seated Position
[See subsections ...]
-
Figure M1: Overview of M301 Diagnostic Equipment for Use by a Patient in a Supine, Prone, or Side-Lying Position
[See subsections ...]
-
Size and Clearances [4.21.2]
Size and Clearances [4.21.2] Lavatories can be located within the clear floor space (as shown in ADAAG Figure 35)....
-
RECOMMENDATIONS
Permit rear or floor mounted swing-away grab bars on both sides of the toilet....
-
11B-805 Medical care and long-term care facilities
SECTIONS 11B-805 Medical care and long-term care facilities 11B-805.4.1 Beds, exam tables, procedure tables, gurneys and lounge chairs. A 36-inch (914 mm) minimum wide...
-
4.3.5 Turning clearance
4.3.5 Turning clearance The ADA-ABA Standards include requirements for a circular turning space, a T shaped turning space, a L-Turn (90-degree turn) and a U-Turn (180-degree turn) around...
-
1607A.8 Loads on hand mils, guards, grab bars and seats
[See subsections ...]
-
Q3.) What are the types of “manufacturing processes” that were anticipated where the advisory says “tolerances recognized by this provision include… “those that may be a necessary consequence of a particular manufacturing process”?
Similarly, the surfaces of ceramic tiles that form the wall behind a grab bar will not be perfectly flat due the manufacturing processes that make them. ...
-
608.2 Size and Clearances for Shower Compartments
608.2 Size and Clearances for Shower Compartments. Shower compartments shall have sizes and clearances complying with 608.2....
-
604.3.2 Overlap
The required clearance around the water closet shall be permitted to overlap the water closet, associated grab bars, dispensers, sanitary napkin disposal units, coat hooks, shelves, accessible...
-
1003.3.1 Boat Slip Clearance
1003.3.1 Boat Slip Clearance. Boat slips shall provide clear pier space 60 inches (1525 mm) wide minimum and at least as long as the boat slips....
-
Other Requirements in the ADA Standards
Automated Doors Maneuvering clearance is required on the egress side of automated doors unless they are equipped with standby power or they stay open in power-off mode (§404.3.2)...
-
404.1 General
404.1 General. Doors, doorways, and gates that are part of an accessible route shall comply with 404. EXCEPTION: Doors, doorways, and gates designed to be operated only by...
-
404.1 General
Doors, doorways, and gates that are part of an accessible route shall comply with 404. EXCEPTION: Doors, doorways, and gates designed to be operated only by security personnel...
-
404.1 General
Doors, doorways, and gates that are part of an accessible route shall comply with 404. EXCEPTION: Doors, doorways, and gates designed to be operated only by security personnel...