[See subsections ...]
Search Results "Patient Change Area"
-
Common Use Circulation Paths in Employee Work Areas Over 1,000 SF
-
Accessible Routes
The accessible route must comply with ADAAG provisions for the location, width (minimum of 36 inches), passing space, head room, surface, slope (maximum of 1:12 or 8.33%), changes in level...
-
11B-305.2 Floor or ground surfaces
Changes in level are not permitted. Exception: Slopes not steeper than 1:48 shall be permitted...
-
11B-305.2 Floor or ground surfaces
Changes in level are not permitted. Exception: Slopes not steeper than 1:48 shall be permitted....
-
Attorney areas and witness stands. (Section-by-Section Analysis)
Attorney areas and witness stands....
-
M302.2.1 Height
The height of the transfer surface during patient transfer shall be 17 inches (430 mm) minimum and 19 inches (485 mm) maximum measured from the floor to the top of the transfer surface....
-
305.2 Floor or Ground Surfaces
Changes in level are not permitted. [ECTCR UFAS 4.2.4.3] EXCEPTION: Slopes not steeper than 1:48 shall be permitted....
-
Element-by-element safe harbor for public accommodations. (Section-by-Section Analysis)
These incremental changes were made to address technological changes that have occurred since the promulgation of the 1991 Standards, to reflect additional study by the Access Board, and...
-
221.2.1.1 General Seating
Table 221.2.1.1 Number of Wheelchair Spaces in Assembly Areas Number of Seats Minimum Number of Required Wheelchair Spaces 4...
-
305.2 Floor or Ground Surfaces
Changes in level are not permitted. EXCEPTION: Slopes not steeper than 1:48 shall be permitted....
-
Ronick Matting Systems BaseMat 300 Entrance Floor Mat
BaseMat 300 Entrance Floor Mat The BaseMat is an economical solution for stopping dirt, snow, and debris from entering your building. At 3/8" depth this aluminum entrance floor...
-
F203.4 Raised Areas
Areas raised primarily for purposes of security, life safety, or fire safety, including but not limited to, observation or lookout galleries, prison guard towers, fire towers, or life guard...
-
203.3 Raised Areas
Areas raised primarily for purposes of security, life safety, or fire safety, including but not limited to, observation or lookout galleries, prison guard towers, fire towers, or life guard...
-
F221.2.1.1 General Seating
[ECTCR UFAS 4.1.2(18)(a) depending on assembly size] Table F221.2.1.1 Number of Wheelchair Spaces in Assembly Areas Number of Seats Minimum Number of Required Wheelchair...
-
Side reach (Section-by-Section Analysis)
If the pay phones comply with the 1991 Standards, the adoption of the 2010 Standards does not require retrofitting of these elements to reflect incremental changes in the 2010 Standards....
-
Side reach (Section-by-Section Analysis)
If the pay phones comply with the 1991 Standards or UFAS, the adoption of the 2010 Standards does not require retrofitting of these elements to reflect incremental changes in the 2010 Standards...
-
M303.2.3.1 Front or Rear Entry
Where wheelchair space entry and exit is provided at only one end (front or rear) the wheelchair space shall be 48 inches (1220 mm) deep minimum.
-
M305.3 Standing Supports
Standing supports shall provide continuous support throughout use of the diagnostic equipment and shall comply with M305.3.
-
M303.2.3.3 Side Entry
Where wheelchair space entry is only from the side, the wheelchair space shall be 60 inches (1525 mm) deep minimum.
-
M303.2.3.2 Pass Through Entry
Where wheelchair space entry and exit permits pass through from one end to the other, the wheelchair space shall be 40 inches deep (1015 mm) minimum.
-
M304.2.2 Standing Supports
Standing supports shall be provided on two sides of the standing surface and shall comply with M305.3. EXCEPTION: Diagnostic equipment with entry and exit permitting pass-through...
-
Physical Access
Resources found at http://www.hfcdihp.org/products.html Choosing and Negotiating an Accessible Facility Location Improving Accessibility with Limited...
-
M304.3 Standing Supports
Standing supports shall be provided on each side of the standing surface and shall comply with M305.3.
-
M305.3 Standing Supports
Standing supports shall provide continuous support throughout use of the diagnostic equipment and shall comply with M305.3.
