ETA Editor's Note The 2010 CBC excerpt and Figures below are from the 2010 CBC Supplement dated August 1, 2012. ...
Search Results "Assurances from Contractors"
-
1115B.4.1, Item 1
-
Transfer Surface Height (M301.2.1 and M302.2.1)
The transfer surface height is also critical for patients who use mobility aids such as walkers and canes and may find it difficult to get up onto or down from an examination chair or table...
-
2.2.3 Functional Reach
The point data were used to measure reach distances from reference points (e.g. maximum forward reach from the front of the WhMD, or maximum side reach from the lateral-most point of the...
-
Widgit First Response Communication Book
This book is designed to help responders to medical emergencies ask questions and understand responses from people for whom communication is difficult....
-
Floor or Ground Surfaces: ADA Standard Section 502.4
Section 502.4 covers the current ADA Standards for the floor or ground surfaces of accessible parking spaces.
-
11B-812.5.1 Accessible route to building or facility
complying with Section 11B-812 shall be permitted to be located in different EV charging facilities if substantially equivalent or greater accessibility is provided in terms of distance from...
-
11B-812.5.1 Accessible route to building or facility
complying with Section 11B-812 shall be permitted to be located in different EV charging facilities if substantially equivalent or greater accessibility is provided in terms of distance from...
-
F203.1 General
Sites, buildings, facilities, and elements are exempt from these requirements to the extent specified by F203....
-
Closed Functionality
Characteristics that limit functionality or prevent a user from attaching or installing assistive technology....
-
12162(a)(2)(C)(i)
(i) be able to be entered from the station platform by an individual who uses a wheelchair; or...
-
6b.
Is the change in level from the floor to the lift surface ramped or beveled? Yes _____ No _____...
-
E202.1 General
ICT shall be exempt from compliance with the 508 Standards to the extent specified by E202....
-
4.31.8 Cord Length
The cord from the telephone to the handset shall be at least 29 in (735 mm) long....
-
4.31.8 CORD LENGTH
The cord from the telephone to the handset shall be at least 29 in (735 mm) long....
-
Benefits Not Monetized in the Formal Analysis
Finally, the RIA recognizes that additional benefits are likely to result from the new standards. Many of these benefits are more difficult to quantify....
-
Benefits Not Monetized in the Formal Analysis
Finally, the RIA recognizes that additional benefits are likely to result from the new standards. Many of these benefits are more difficult to quantify....
-
407.2.2.2 Visible Signals
Signals shall be visible from the floor area adjacent to the hall call button. EXCEPTIONS: 1....
-
1.9.1.8 Adopting agency identification
ETA Editor's Note Sections from California Building Code Chapter 1 not adopted by Division of the State Architect - Access Compliance (DSA-AC) omitted. ...
-
604.9.1 Location
The centerline of the water closet shall be 12 inches (305 mm) minimum and 18 inches (455 mm) maximum from the side wall or partition, except that the water closet shall be 17 inches (430...
-
M302.4.1 Clearance in Base
The base of the diagnostic equipment shall provide a clearance 39 inches (990 mm) wide minimum, 6 inches (150 mm) high minimum measured from the floor, and 36 inches (915 mm) deep minimum...
-
M301.4.1 Clearance in Base
The base of diagnostic equipment shall provide a clearance 39 inches (990 mm) wide minimum, 6 inches (150 mm) high minimum measured from the floor, and 36 inches (915 mm) deep minimum measured...
-
3. Lavatory knee clearance
clearance under the front edge of the lavatory, the top of the bowl mounted no higher than 34 inches above the floor, a 27-inch-high clearance for knee space extending at least 8 inches from...
-
607.4.2.1 Back Wall
Each grab bar shall be 24 inches (610 mm) long minimum and shall be installed 24 inches (610 mm) maximum from the head end wall and 12 inches (305 mm) maximum from the control end wall....
-
703.4.1 Height Above Finish Floor or Ground
Tactile characters on signs shall be located 48 inches (1220 mm) minimum above the finish floor or ground surface, measured from the baseline of the lowest tactile character and 60 inches...