A religious corporation, association, educational institution, or society is permitted to give preference in employment to individuals of a particular religion to perform work connected...
Search Results "Direct Connection"
-
§1630.16(a) Religious entities
-
1130A.1 General
The accessible route shall pass through the primary entry door, and shall connect with all additional exterior doors, required clear floor spaces at kitchen appliances and bathroom fixtures...
-
ADJUSTED CONSTRUCTION COST
The adjusted construction cost shall not include: project management fees and expenses, architectural and engineering fees, testing and inspection fees, and utility connection or service...
-
11B-806.3.2 Notification devices
Notification devices shall not be connected to visible alarm signal appliances....
-
ADJUSTED CONSTRUCTION COST
The adjusted construction cost shall not include: project management fees and expenses, architectural and engineering fees, testing and inspection fees, and utility connection or service...
-
11B-806.3.2 Notification devices
Notification devices shall not be connected to visible alarm signal appliances....
-
1130A.1 General
The accessible route shall pass through the primary entry door, and shall connect with all additional exterior doors, required clear floor spaces at kitchen appliances and bathroom fixtures...
-
11B-406.3.2 Turning space
The slope of the turning space in all directions shall be 1:48 maximum. FIGURE 11B-406.3.2 ‡‡ PARALLEL CURB RAMPS...
-
ACCESSIBILITY FUNCTION BUTTON
destination-oriented elevator system that when pressed will activate a series of visual and verbal prompts and announcements providing instruction regarding hall call console operation and direction...
-
1012.5 Slope
The slope of the surface of parking spaces and pull-up spaces shall not be steeper than 1:48 in any direction....
-
1132A.4, Item 5
In buildings containing covered multifamily dwelling units, the floor or landing immediately outside the entry may be sloped up to ¼ inch (6.35 mm) per foot (12 inches) (305 mm), in a direction...
-
1015.6 Slope
The slope of the surface of clear ground spaces and turning spaces shall not be steeper than 1:48 in any direction....
-
C201.3 Access to Functionality (Section-by-Section Analysis)
Section-by-Section Analysis) This section proposes that telecommunications equipment manufacturers ensure that ICT is accessible to, and usable by, individuals with disabilities by providing direct...
-
5.1.8 Slope
The slope of the surface of the clear ground space shall not be steeper than 1:48 in any direction....
-
Cross Slope
The percentage of rise to length, which is the difference in elevation, when measuring the trail tread from edge to edge perpendicular to the direction of travel This may be expressed as...
-
3.4.7 Openings
Where possible, elongated openings should be placed perpendicular, or as close to perpendicular as possible, to the dominant direction of travel....
-
1012.5 Slope
The slope of the surface of parking spaces and pull-up spaces shall not be steeper than 1:48 in any direction....
-
1015.6 Slope
The slope of the surface of clear ground spaces and turning spaces shall not be steeper than 1:48 in any direction....
-
11B-411.2.1.2.4 Display screen
accessibility function button, the display screen shall display information including but not limited to, operating instructions, user input confirmation, elevator assignment characters, direction...
-
1132A.4, Item 5
In buildings containing covered multifamily dwelling units, the floor or landing immediately outside the entry may be sloped up to ¼ inch (6.35 mm) per foot (12 inches) (305 mm), in a direction...
-
§ 38.159(d)(5) Movement
secured in accordance with manufacturer's instructions, the securement system shall limit the movement of an occupied wheelchair or mobility aid to no more than 2 inches (50 mm) in any direction...
-
11B-411.2.1.2.4 Display screen
accessibility function button, the display screen shall display information including but not limited to, operating instructions, user input confirmation, elevator assignment characters, direction...
-
Transfer Supports Location and Configuration M301.3 and M302.3
The shape (contours and curves along length for ergonomics, not cross sectional profile) was kept open to give manufacture flexibility in the design as the direction of positioning (i.e....
-
B. Executive Order 13132 (Federalism)
This final rule does not include any provision that: (1) Has substantial direct effects on the States, the relationship between the national government and the States, or the distribution...