Changes in level greater than ½ inch (13 mm) high shall be ramped and shall comply with M303.3.3.
Search Results "Transfer Platform"
Filters
Commonly Searched Documents
-
M303.3.3 Ramped
-
M303.3.3.4 Edge Protection
Ramps with drop offs ½ inch (13 mm) or greater shall provide edge protection 2 inches (50 mm) high minimum on each side.
-
M301.3 Supports
Transfer supports, stirrups, and reclining surfaces shall comply with M301.3....
-
M301.3 Supports
Transfer supports, leg supports, and reclining surfaces shall comply with M301.3....
-
1009.2 Continuity and components
Platform lifts complying with Section 1009.5, and Chapter 11A, Section 1124A, or Chapter 11B, Sections 11B-207, 11B-207.2 and 11B-410 as applicable....
-
Aquatic Recreation Facilities
The accessible means of entry can be either a pool lift, sloped entry, or transfer system....
-
Certain Sports/ Recreation and Other Structures (§203.10 - §203.14)
are also exempt: raised structures used solely for refereeing, judging, or scoring a sport raised boxing/ wrestling rings water slides and raised diving boards/ platforms...
-
Section 35.151(g) Assembly Areas (Section-by-Section Analysis)
These platforms cover one or more rows of non-wheelchair seating. ...
-
M305.2.8 Fittings (Section-by-Section Analysis)
supports to be moved out of the way after transfer....
-
Scoping [4.1.3(5)]
Elevators are required in "multi-story" facilities. There may be more than one floor level, such as a mezzanine, within a "story" but the requirement for an elevator applies to...
-
VOLUNTARY COMPLIANCE AGREEMENT
BETWEEN
THE UNITED STATES OF AMERICA
AND
THOMAS JEFFERSON UNIVERSITY HOSPITALS INC.
&
OUTPATIENT IMAGING AFFILIATES, LLC.
DJ# 202-62-458
VOLUNTARY COMPLIANCE AGREEMENT BETWEEN THE UNITED STATES OF AMERICA AND THOMAS JEFFERSON UNIVERSITY HOSPITALS INC. & OUTPATIENT IMAGING AFFILIATES, LLC. DJ# 202-62-458
-
M305.2.8 Fittings
Transfer supports shall not rotate within their fittings when in place for transfer....
-
M305.2.2 Length (Section-by-Section Analysis)
table at the designated transfer location for at least the minimum width of the transfer surface, with a minimum length of 28 inches....
-
Section 35.151(g) Assembly areas (Section-by-Section Analysis)
These platforms cover groups of conventional seats and are used to provide groups of wheelchair seats and companion seats....
-
M305.2.7 Clearance (Section-by-Section Analysis)
In the MDE NPRM, the Access Board did not provide any specific requirements for clearances around the transfer support....
-
M305.2.2 Length
The length of transfer supports shall comply with M305.2.2.1 or M305.2.2.2....
-
A4.22.3 Clear Floor Space
The dotted lines designate the minimum clear floor space, depending on the direction of approach, required for wheelchair users to transfer onto the water closet....
-
1003.2.13.1 General.
Platform lifts complying with Section 1003.2.13.4. Horizontal exits. Smoke barriers....
-
Tips for Weighing People Using an Accessible Scale
Sloped surface provides access to scale platform -- no abrupt level changes at floor or platform. Edge protection at drop off....
-
§ 36.406(f) Assembly areas
(f) Assembly areas. Assembly areas subject to the proposed standards shall comply with the provisions applicable to assembly areas, including, but not limited to, sections 221 and...
-
§ 36.406(f) Assembly areas
(f) Assembly areas. Assembly areas subject to this section shall comply with the provisions of the 2010 Standards applicable to assembly areas, including, but not limited to,...
-
11B-705.1.1.3 Color and contrast
11B-705.1.1.3 Color and contrast. Detectable warning surfaces shall comply with Section 11B-705.1.1.3.1. The material used to comply with this section shall be an integral part of...
-
Bobrick 18" Straight Grab Bar Peened B-6806.99 x 18
18" (455mm) long, 1-1/2" (38mm) dia. tubing, peened finish. Constructed of 18-gauge (1.2mm), type 304 satin-finish stainless steel tubing. Concealed mounting flange 1/8" (3mm) thick,...
-
Delta 1-1/2″ x 18″ ADA Grab Bar, Concealed Mounting 40118-PS
Product Features and Benefits 18″ long, 1 1/2″ wide Concealed mounting - mounting hardware included 3″ diameter flanges 1 1/2″ wall clearance Limited Faucet and Finish...
