If the ramp or landing has a vertical drop-off on either side, is edge protection provided? [ADA Standards § 4.8.7] Yes No...
Search Results "Ramp Surface"
Filters
Commonly Searched Documents
-
f-viii
-
11B-809.9.4 Work surfaces
Work surfaces shall be 36 inches (914 mm) maximum above the finish floor with minimum lengths at the following locations as required by this section: Linear length of 30 inches...
-
Pemko 193 Slip resistance
By slip resistance I am assuming it will meet the coefficient of friction requirement of 0.8 if installed on a ramp. Thank you -Brian...
-
902.3 Baby Changing Table Work Surface Height
-
Macro Supa-Trac Rigid Ground Cover
Requires the Premium User plan or above. (Login or upgrade your account!) -
R304.5.1 Width
The clear width of curb ramp runs (excluding any flared sides), blended transitions, and turning spaces shall be 1.2 m (4.0 ft) minimum....
-
Resting Intervals [1018.8]
When the surface of the resting interval is constructed of asphalt, concrete, or boards, the slope of the resting interval must be no steeper than 1:48 (2 percent) in any direction....
-
Curb Ramps at Intersections
Curb ramps at marked crossings must be wholly contained within the crosswalk, excluding side flares....
-
Installation
Installation Surface materials/systems were installed by both contractors and the playground owners’ maintenance staff. ...
-
Interior Routes
INTERIOR ROUTES Floor and ground surfaces stable, firm and slip resistant. 11B-302.1 Carpet pile height 1/2 inch...
-
Interior Routes
INTERIOR ROUTES Floor and ground surfaces stable, firm and slip resistant. 11B-302.1 Carpet pile height 1/2 inch...
-
5.2.2 Transfer Surface Size Recommendations for M302
5.2.2 Transfer Surface Size Recommendations for M302 Description: The transfer surface is the part of the diagnostic equipment onto which patients who use mobility devices or aids transfer...
-
§ 38.95(c)(6)(ii) Exception
Ramps or bridge plates which are attached to, and deployed from, station platforms are permitted in lieu of car devices provided they meet the displacement requirements of paragraph (c)(...
-
(1) Transfer Surface Location for Diagnostic Equipment Used in the Supine, Prone, or Side-lying Position
its depth spanned the examination surface’s width, and was located near the center point of the diagnostic equipment surface....
-
Can handrails be mounted to guard rails?
Yes, handrails can be installed on guard rails if all applicable requirements are met.
-
B7-b
Is the slope (up or down the ramp) no more than 1:12? [ADA Standards § 4.7.2] Yes No Note: 1:12 is one inch of vertical height for each 12 inches of length....
-
Hager Companies Door Protection Plate 198S
Door Protection Plate 198S 0.038" gauge stainless steel Materials: - Stainless Steel
-
Hager Companies Door Protection Plate 194S
Door Protection Plate 194S 0.050" gauge with 4-sided bevel Materials: - Aluminum, Brass, Bronze, Stainless Steel
-
Hager Companies Door Protection Plate 199B
Door Protection Plate 199B 0.038" gauge aluminum Materials: - Aluminum Finishes: - Bright gold anodized
-
Hager Companies Door Protection Plate 224S
Door Protection Plate 224S 0.062" gauge with 4-sided bevel Materials: - Aluminum, brass, bronze, stainless steel Options: - Self-adhesive tape available on all plates -...
-
Don-Jo Mfg., Inc. Push Plate 69
Product Specifications Number 69 Dimensions 3" x...
-
Hager Companies Door Protection Plate 220S
Door Protection Plate 220S 0.062" gauge with no bevel Materials: - Aluminum, brass, bronze, stainless steel Options: - Self-adhesive tape available on all plates -...
-
Hager Companies Door Protection Plate 190S
Door Protection Plate 190S 0.050" gauge with no bevel Options: - UL listed for US32 and US32D with screw fasteners (must specify UL stamp) - Self-adhesive tape available...
-
Hager Companies Door Protection Plate 223S
Door Protection Plate 223S 0.062" gauge with 3-sided bevel Materials: - Aluminum, brass, bronze, stainless steel Options: - Self-adhesive tape available on all plates -...
