Door Protection Plate 224S 0.062" gauge with 4-sided bevel Materials: - Aluminum, brass, bronze, stainless steel Options: - Self-adhesive tape available on all plates -...
Search Results "Ramp Surface"
Commonly Searched Documents
- Hager Companies Door Protection Plate 224S
- Hager Companies Door Protection Plate 199B
- Don-Jo Mfg., Inc. Push Plate 69
- Hager Companies Door Protection Plate 214S
-
4.7.2 SLOPE
Slopes of curb ramps shall comply with 4.8.2. The slope shall be measured as shown in Fig. 11....
-
5 [§ 4.7.2]
5 [§ 4.7.2] The transitions on and off the curb ramp are the points where the gutter meets the bottom of the ramp and where the top of the ramp meets the sidewalk....
-
4.7.2 Slope
Slopes of curb ramps shall comply with 4.8.2. The slope shall be measured as shown in Fig. 11....
-
Doorways [4.8.4]
Recommendation: Ramps and doors should be configured to facilitate wheelchair maneuvering and to prevent open doors from obstructing ramp openings (important along egress routes)....
-
Development of Surface Roughness Standards for Pathways Used by Wheelchair Users: Final Report
Development of Surface Roughness Standards for Pathways Used by Wheelchair Users: Final Report December 2014 Human Engineering Research Laboratories VA Pittsburgh Healthcare System...
-
9.a [§ 4.7.5]
9.a [§ 4.7.5] If the sidewalk at the top of the ramp (“x” in the illustration) is 48 inches wide or more, answer this question....
-
R304.3.2 Running Slope
The running slope of the curb ramp shall be in-line with the direction of sidewalk travel....
-
11B-902.4.2 Height
The tops of tables and counters shall be 26 inches (660 mm) minimum and 30 inches (762 mm) maximum above the finish floor or ground.
-
Mirror Height
The guidelines specify that accessible mirrors be mounted so that the bottom edge of the reflecting surface is no higher than 40 inches (603.3)....
-
National Trail Surfaces Study Final Report
National Trail Surface Study Final Report February 2014 Staff Liaison Bill Botten U.S....
-
11B-606.5 Exposed pipes and surfaces
There shall be no sharp or abrasive surfaces under lavatories and sinks....
-
11B-606.5 Exposed pipes and surfaces
There shall be no sharp or abrasive surfaces under lavatories and sinks....
-
Medical Diagnostic Equipment Accessibility Standards Sub-Committee Recommendations Weight Scales
Types Of Equipment To Which Technical Criteria Applies Seated in a wheelchair (M303) Wheelchair space, including orientation, width, depth, knee and toe clearance, and surface...
- Inpro Corporation JointMaster® AR Series Seal Expansion Joint Systems
-
Material Characteristics (slide 6)
Matte finishes (slide 6) are always better than specular surfaces or polished granite. And that can be columns, and it can even be lighting fixtures....
- Simplified Building Kee Access ADA Railings
-
3a.
If yes, is a ramp or sloped hallway provided? Yes _____ No _____ If yes, go to question E1-4. Note: A ramp, lift, or elevator can be used to provide access to floor levels....
-
R304.2.2 Running Slope
The running slope of the curb ramp shall cut through or shall be built up to the curb at right angles or shall meet the gutter grade break at right angles where the curb is curved....
-
§ 38.159(b)(8) Platform entrance ramp
(8) Platform entrance ramp....
-
Designing Sidewalks and Trails for Access, Part II of II: Best Practices Design Guide
This guidebook is the second part of a two-phase project focused on designing sidewalks and trails for access. It was created to provide planners, designers, and transportation...