The number of adaptable residential dwelling units required in non-elevator building public housing facilities shall be determined in accordance with Chapter 11A, Section 1150A.1....
Search Results "Non-Glare Finish"
Filters
Commonly Searched Documents
-
11B-233.3.1.2.5 Public housing facility site impracticality
-
Grab Bars
The diameter of the grab bars must comply with ADAAG (diameter between 1.25 and 1.5 inches, not abrasive, and non-rotating)....
-
Starting Your Plan with Preparedness
There is plenty to do during non-emergency times to make sure your community is prepared. With this section you will start developing your community’s emergency plan....
-
Angled Van Spaces
Recommendation: Where standard (non-van) accessible spaces are angled or otherwise restrict entry to one direction only, providing one access aisle for each accessible space (or on both...
-
68.73. Registration Requirements--Renewal
(b) Non-receipt of a registration renewal notice from the department does not exempt a person from any requirements of this chapter....
-
D. Suites:
these suites later be marketed or sold to the public on a season basis, PSE shall make the suites (including the toilet rooms) accessible in compliance with the 2010 Standards, as they are non-complying...
-
Error/Omission: The built-up curb ramp projects into the access aisle.
* Asterisk denotes that related, non-mandatory material is in the Appendix to the Standards....
-
11B-233.3.1.2.6 Public housing facility site impracticality
The number of adaptable residential dwelling units required in non-elevator building public housing facilities shall be determined in accordance with Chapter 11A, Section 1150A.1....
-
Section 37.81 Purchase or Lease of Used Rail Vehicles by Public Entities Operating Rapid or Light Rail Systems
The requirements and standards are the same as those specified for non-rail vehicles in §37.73....
-
ACTIONS TO BE TAKEN BY CAMP BRAVO
Camp Bravo will adopt, maintain, and enforce the non-discrimination statement attached hereto and incorporated by reference herein as Exhibit 1 to this Agreement. ...
-
M305.2.4 Cross Section (Section-by-Section Analysis)
Specifically, the Access Board indicated it was considering requiring circular cross sections to have an outside diameter of 1¼ inches minimum and 2 inches maximum, and transfer supports with non-circular...
-
11B-805 Medical care and long-term care facilities
The 18 inch strike-side clearance and 5 feet deep maneuvering clearance are not required at the patient room door in a "non-accessible room," as one not required to provide mobility features...
-
Use color and design to create architectural landmarks to aid in spatial orientation (slides 8 – 10)
Now, yes, there’s a lot of glare in this space. It was an east-facing wall looking over the Mississippi River....
-
Technical Memorandum TM 2017-25 Door and Gate Surfaces
TM 2017-25 Door and Gate Surfaces Effective Date: April 1, 2017 2012 TAS Reference: 404.2.10 404.2.10 requires door and gate surfaces within 10 inches (255mm) of the finish...
-
ACCESSIBLE DWELLING UNITS
Requires the Accessibility Specialist plan or above. (Login or upgrade your account!)
-
704.4.1 Height
When in use, the touch surface of TTY keypads shall be 34 inches (865 mm) minimum above the finish floor....
-
STORY
If the finished floor level directly above a basement or unused under-floor space is more than six feet (1829 mm) above grade for more than 50 percent of the total perimeter or is more than...
-
608.3 Grab Bars
Where multiple grab bars are used, required horizontal grab bars shall be installed at the same height above the finish floor....
-
704.4.1 Height
When in use, the touch surface of TTY keypads shall be 34 inches (865 mm) minimum above the finish floor....
-
610.3 Shower Compartment Seats
The top of the seat shall be 17 inches (430 mm) minimum and 19 inches (485 mm) maximum above the bathroom finish floor. Seats shall comply with 610.3.1 or 610.3.2....
-
307.2 Protrusion Limits
Objects with leading edges more than 27 inches (685 mm) and not more than 80 inches (2030 mm) above the finish floor or ground shall protrude 4 inches (100 mm) maximum horizontally into...
-
Facility
The tops of dining surfaces and work surfaces shall be 28 inches minimum and 34 inches maximum above the finish floor or ground....
-
Effective Communication
Staff and county officials must take the time to listen to N.M, not interrupt him or finish his sentences....