It's ideal for exiting sits, where major construction is not possible. Features Top landing includes a 42" gate, fire door, RDI interlock or flush strike....
Search Results "Horizontal Exit"
-
Harmar TG400 Toe Guard Commercial Platform Lift
-
382.97 To which aircraft does the requirement to provide boarding and deplaning assistance through the use of lifts apply?
serious damage to the aircraft or injury to persons, or that there are internal barriers in the aircraft that would preclude passengers who use a boarding or aisle chair from reaching a non-exit...
-
Is Identification of Which Means of Egress Are Available/Closest Necessary?
These plans should be given to visitors when they enter the building so they can find the exits in an emergency....
-
Verbalizing Directions
Indicate number of blocks to the department store and whether one proceeds right or left when exiting the hotel....
-
Create an Emergency Plan for Your Home
(Bondi 2001) In addition to basic fire safety guidelines such as installing smoke alarms and changing the batteries regularly, make sure you have more than one way to exit your homes and...
-
3306.2 Walkways
A walkway shall be provided for pedestrian travel that leads from a building entrance or exit of an occupied structure to a public way....
-
1117B.5.7
Signs that identify exits shall be located on the approach side of the door as one exits the room or space....
-
Only Safety Affects Seat Assignments
Only Safety Affects Seat Assignments You must not exclude a passenger with a disability from any seat in an exit row or other location or require a passenger with a disability to sit...
-
Walk Through Procedures
Know how to get to all the exits. Practice this as part of your regular drills....
-
11B-405.9 Edge protection
Edge protection shall not be required on the sides of ramp landings having a vertical drop-off of ½ inch (12.7 mm) maximum within 10 inches (254 mm) horizontally of the minimum landing area...
-
Issue 9: Reach (how far?)
APS should be within the reach range (1.2 m/48 inches vertically, .25m/10 inches horizontally) for an individual who uses a wheelchair (draft PROWAG, R404)....
-
M305.3.2 Height (Section-by-Section Analysis)
For horizontal supports, the MDE NPRM proposed a gripping surface height of 34 inches minimum and 38 inches maximum above the standing surface....
-
Handrails
Where provided, horizontal projections shall occur 1 1/2 inches (38 mm) minimum below the bottom of the handrail gripping surface....
-
608.3 Grab Bars
Where multiple grab bars are used, required horizontal grab bars shall be installed at the same height above the finish floor. EXCEPTIONS: 1....
-
608.3 Grab Bars
Where multiple grab bars are used, required horizontal grab bars shall be installed at the same height above the finish floor. EXCEPTIONS: 1....
-
Grade (R302.5) (Section-by-Section Analysis)
Grade is calculated by dividing the vertical change in elevation by the horizontal distance covered, and is expressed as a percent....
-
1.1.12 Ramp cross slope
overall cross slope of ramps by establishing elevations at the extreme edges of the ramp at the top and bottom of the ramp and calculate the cross slope at these two locations using the horizontal...
-
Stairs
At the bottom, the handrail shall continue to slope for a distance of the width of one tread from the bottom riser; the remainder of the extension shall be horizontal (see Fig. 19(c) and...
-
11B-405.9 Edge protection
Edge protection shall not be required on the sides of ramp landings having a vertical drop-off of ½ inch (12.7 mm) maximum within 10 inches (254 mm) horizontally of the minimum landing area...
-
1009.7.2 Separation
The fire-resistance-rated exterior wall construction shall extend horizontally 10 feet (3048 mm) beyond the landing on either side of the landing or equivalent fire-resistance-rated construction...
-
11B-405.9 Edge protection
Edge protection shall not be required on the sides of ramp landings having a vertical drop-off of ½ inch (12.7 mm) maximum within 10 inches (254 mm) horizontally of the minimum landing area...
-
M305.3 Standing Supports (Section-by-Section Analysis)
This provision has been reorganized in the final rule into requirements for length and height, as opposed to vertical and horizontal....
-
703.5.5 Character Height
Viewing distance shall be measured as the horizontal distance between the character and an obstruction preventing further approach towards the sign....
-
Fixed position maps and kiosks
While it is normally more convenient and practical to mount these maps on vertical surfaces, as is typical for publicly displayed maps, it is better to place tactile maps on a horizontal...