Landings shall be provided at the tops of curb ramps. The landing clear length shall be 36 inches (915 mm) minimum....
Search Results "Ramp Surface"
-
406.4 Landings
-
1.2.2
1.2.2 When flatness of running slope for an accessible surface other than a ramp is measured according to Section 1.1.5 no more than 20% (rounded to the nearest whole number) of the measurements...
-
A7
Is the width of the curb ramp surface at least 36 inches (not counting the side flares)? [ADA Standards § 4.7.3] Yes No...
-
B7-a
Is the curb ramp surface at least 36 inches wide, excluding flared sides? [ADA Standards § 4.7.3] Yes No...
-
6. Ramps
Ramps 4.8 Accessible routes with slopes greater than 1:20....
-
Transfer Surface Size: Equipment Used by Patients in a Seated Position (M302.2.2)
On diagnostic equipment used by patients in a seated position, M302.2.2 would require the size of the transfer surface to be 21 inches wide minimum and 15 inches deep minimum....
-
406.4 Landings
Landings shall be provided at the tops of curb ramps. The landing clear length shall be 36 inches (915 mm) minimum....
-
e-i
Is the curb ramp surface at least 36 inches wide, excluding flared sides? [ADA Standards § 4.7.3] Yes No...
-
11B-302.3 Openings
Openings in floor or ground surfaces shall not allow passage of a sphere more than ½ inch (12.7 mm) diameter except as allowed in Sections 11B-407.4.3 _|Platform to Hoistway Clearance|_,...
-
Current industry standard practices resulting from this project
Studies were repeated in 2003 and 2004 to determine the effects of environmental factors and evaluate additional surface types....
-
Error/Omission: The built-up curb ramp projects into the access aisle.
Error/Omission: The built-up curb ramp projects into the access aisle. The accessible parking space and access aisle is not level in all directions....
-
4 - Best practices for construction observation
For large projects for where extensive accessible surfaces are required, early checking should be done to suggest needed adjustments to construction techniques....
-
11B-804.3 Kitchen work surface
In residential dwelling units required to comply with Section 11B-809, at least one 30 inches (762 mm) wide minimum section of counter shall provide a kitchen work surface that complies...
-
11B-804.3 Kitchen work surface
In residential dwelling units required to comply with Section 11B-809, at least one 30 inches (762 mm) wide minimum section of counter shall provide a kitchen work surface that complies...
-
11B-406.3.2 Turning space
A turning space 48 inches (1219 mm) minimum by 48 inches (1219 mm) minimum shall be provided at the bottom of the curb ramp....
-
11B-406.3.2 Turning space
A turning space 48 inches (1219 mm) minimum by 48 inches (1219 mm) minimum shall be provided at the bottom of the curb ramp....
-
EXHIBIT A Required Accessible Elements at QuikTrip Stores
along both sides of the ramp extending at least 12 inches beyond the top and bottom of the ramp parallel with the ground surface; the handrails do not rotate within their fittings; and...
-
Boarding Pier Clearances: ADA Standard Section 1003.3.2
The following example applies to a boat launch ramp boarding pier: A chain of floats is provided on a launch ramp to be used as a boarding pier which is required to be accessible by 1003.3.2...
-
Fittings: ADA Standard Section 505.9
Section 505.9 covers the current ADA Standards for handrail fittings.
-
11B-505.9 Fittings
Handrails shall not rotate within their fittings.
-
11B-405.7.1 Slope
Landings shall comply with Section 11B-302. Changes in level, slopes exceeding 1:48, and detectable warnings shall not be permitted. Exception: Reserved.
-
11B-405.7.1 Slope
Landings shall comply with Section 11B-302. Changes in level, slopes exceeding 1:48, and detectable warnings shall not be permitted. Exception: Reserved.
-
11B-505.9 Fittings
Handrails shall not rotate within their fittings.
-
§ 38.125(c) Car ramp or bridge plate
(c) Car ramp or bridge plate—...