The following technical criteria in the proposed standards are based on the 2004 ADA and ABA Accessibility Guidelines: • Height of transfer surfaces on diagnostic equipment used by patients...
Search Results "Clearance in Base"
Filters
Commonly Searched Documents
-
2004 ADA and ABA Accessibility Guidelines
-
11B-902.4.1 Clear floor or ground space
Knee and toe clearance complying with Section 11B-306 shall be provided, except that knee clearance 24 inches (610 mm) minimum above the finish floor or ground shall be permitted....
-
Transit Shelters (R308.2) (Section-by-Section Analysis)
The turning space would be based on the 2004 ADA and ABA Accessibility Guidelines (see 304.3).43 The turning space would be permitted to overlap the clear space within the transit shelter...
-
Priority 1: Approach & Entrance
Word Fillable Form (1.5MB) Word Non-Fillable Form (1.3MB) PDF Non-Fillable Form (0.8MB)
-
Clear Deck Space
Clear Deck Space Clear deck space of 60 by 60 inches minimum, with a slope of not more than 1:48, must be provided at the base of a transfer wall....
-
Adaptability
This allows structural reinforcement or blocking for later installation of grab bars and removable base cabinetry below lavatories....
-
M101.3 Equivalent Facilitation
However, the standards include technical criteria for clearance in or around the base of the equipment for lift compatibility to allow the use of a patient lift by patients with disabilities...
-
Ground Level Play Components: ADA Standard Section 240.2.1
Section 240.2.1 covers scoping requirements in the current ADA Standards for ground level play components.
-
Figure 608.2.1 Transfer Type Shower Compartment Size and Clearance – Drawing from the U.S. Access Board
-
11B-813.2.10 Door swing
Where a clear floor space complying with Section 11B-305.3 is provided within the room beyond the arc of the door swing, doors shall be permitted to swing into the clear floor space, clearance...
-
D. Beds in accessible guest rooms and sleeping rooms
Many individuals with disabilities have urged the Department to regulate the height of beds, particularly in accessible hotel guest rooms, and to require that such beds have clearance under...
-
Executive Summary
Key requirements apply to clear floor area, reach limits, knee and toe clearances and maneuvering clearances....
-
Hoyer Heavy-Duty Power Lift with Optional Scale
Description: Hoyer's Heavy-Duty Power Lift features a power operated base with a clearance of 4.5"....
-
Issue 23: Should design guidance for persons with low vision be prescriptive or performance based?
Comment by Marsha Mazz: I don’t know where we’re going with this because as we’ve said, time and time again, the issues of concern to this group here are not addressed by the...
-
Figure 608.2.3 Alternate Roll-In Type Shower Compartment Size and Clearance – Drawing from the U.S. Access Board
-
Figure 608.2.2 Standard Roll-In Type Shower Compartment Size and Clearance – Drawing from the U.S. Access Board
-
Rockwood Manufacturing Company 215 Tapered Door Pull 16"
Options: • Use Y prefix (Y215) when ordering pulls with base plates, Y plate diameter is 1-1⁄16"; recommended for use on glass or wood doors....
-
Rockwood Manufacturing Company 215L Tapered Door Pull 28"
Options: • Use Y prefix (Y215) when ordering pulls with base plates, Y plate diameter is 1-1⁄16"; recommended for use on glass or wood doors....
-
1011.2.1 Size and Location
The size of the clear ground space is based on the dimensions for maneuvering clearance at clear floor or ground spaces that are confined on all or part of three sides in 305.7 of the Architectural...
-
Pilot Rock: Picnic Table ADA Compliance Comparison
The ADA Guidelines define a "clearance box" that must fit under the table to be accessible....
-
Notes
In mammography, the presence of the base support for the physical stability and operation of the equipment falls into this category....
-
11B-603.2.2 Overlap
Required clear floor spaces, clearance at fixtures, and turning space shall be permitted to overlap....
-
11B-813.2.9 Overlap
Required clear floor spaces, clearance at fixtures, and turning space shall be permitted to overlap....
