stowage of cargo in the cabin compartment) in the cabin of sufficient size to stow at least one typical adult-sized folding, collapsible, or break-down manual passenger wheelchair, the dimensions...
Search Results "Maximum Dimension"
-
§382.67(a)
-
HOW TO MEASURE TRANSFER HEIGHTS IS IMPORTANT
Because of these complex shapes, it is necessary to create a standard method by which to measure table seat dimensions....
-
References:
“Revised Knee Clearance Depth and Footrest Clearance dimensions for sizing of mammography equipment.” Memorandum. April 23, 2013....
-
Horizontal Alignment
The critical user for this dimension would be the inline skater....
-
308.2.2 Obstructed High Reach
The high forward reach shall be 48 inches (1220 mm) maximum where the reach depth is 20 inches (510 mm) maximum....
-
11B-809.8.3.1 Floor or ground surface
., concrete, brick, flagstone) may have a maximum change in height from the interior landing of 4 inches (102 mm)....
-
11B-608.6 Shower spray unit and water
Shower spray units shall deliver water that is 120°F (49°C) maximum....
-
11B-608.6 Shower spray unit and water
Shower spray units shall deliver water that is 120°F (49°C) maximum....
-
IDEA Center
This occurs mostly with dimensions near the hands and other body parts that may move slightly during data collection....
-
8.5 Updating Standards in the Future
As noted above, the general population is increasingly overweight and obese; if population heights and weights change significantly, this might alter dimensions required for equipment accessibility...
-
4.1.2 Surface Design of Examination Tables and Chairs
., while patients’ weights are compressing the table’s or chair’s foam padding).Z This dimension is typically measured at the back of a patient’s knees and includes compression of the seat...
-
11B-705.1.1.1 Dome size
Truncated domes in a detectable warning surface shall have a base diameter of 0.9 inch (22.9 mm) minimum and 0.92 inch (23.4 mm) maximum, a top diameter of 0.45 inch (11.4 mm) minimum and...
-
Minimum Number: ADA Standard Section 239.2
Section 239.2 covers scoping requirements in the current ADA Standards for the minimum number of miniature golf course holes that are required to be accessible.
-
Character Height: ADA Standard Section 703.2.5
Character height measured vertically from the baseline of the character shall be 5/8 inch (16 mm) minimum and 2 inches (51 mm) maximum based on the height of the uppercase letter “I”....
-
11B-604.9.5 Flush controls
Hand operated flush controls shall comply with Sections 11B-309.2 and 11B-309.4 and shall be installed 36 inches (914 mm) maximum above the finish floor....
-
DRIVE-UP ELECTRIC VEHICLE CHARGING STATION
An electric vehicle charging station in which use is limited to 30 minutes maximum and is provided at a location where the electric vehicle approaches in the forward direction, stops in...
-
DRIVE-UP ELECTRIC VEHICLE CHARGING STATION
An electric vehicle charging station in which use is limited to 30 minutes maximum and is provided at a location where the electric vehicle approaches in the forward direction, stops in...
-
11B-604.9.5 Flush controls
Hand operated flush controls shall comply with Sections 11B-309.2 and 11B-309.4 and shall be installed 36 inches (914 mm) maximum above the finish floor....
-
Midmark 625 Barrier-Free® Power Examination Table
Optional IQscale® and IQhub®offers a digital scale built into the table and easy access receptacles and data ports Patient Weight Capacity: 650 lb (295 kg) Height: Minimum 18" (46 cm) Maximum...
-
Pilot Rock End Accessible Multi-Pedestal Table APT Series 3"x4" Recycled Plastic
These picnic tables have 8 ft. tops which extend 1 foot beyond each end of the 6 ft. seats, 30" table height and 18" seat height (nominal dimensions). ...
-
R408.5 Nosings
The radius of curvature at the leading edge of the tread shall be 13 mm (0.5 inch) maximum....
-
607.4.1.1 Back Wall
Two grab bars shall be installed on the back wall, one located in accordance with 609.4 and the other located 8 inches (205 mm) minimum and 10 inches (255 mm) maximum above the rim of the...
-
11B-809.8.1 Door Thresholds
Secondary exterior door thresholds, including sliding door tracks, shall be 3/4 inch (19.1 mm) high maximum with a 1:2 maximum slope....
-
Q5.) What dimensions and conditions can practitioners reasonably consider to be compliant when the conditions, as constructed, do not meet the technical requirements exactly and there are no official, published, industry-developed tolerances?
A5.) This is the most difficult question and the most subject to varying opinions. Sloped concrete and asphalt surfaces are an excellent example of this problem. To our...
